Honeywell CGW-MB Скачать руководство пользователя страница 170

Страница: 170 / 187

CGW-MB Installation and Users’ Manual | P/N:LS10248-000HW-E | REV.G | JUL/31/2022

169

Gent Panels

Connecting to the Panels

3. Power Connection

On the CLSS Gateway mainboard Side

1. Connect to the 24V DC external power supply.
2. Ensure that the S7 switch next to the RS-232 port is switched towards

NUP_OUT.

Figure C.23: The S7 Switch

On the Panel Side
Connect the power cable into the 24V DC external power supply.

To Use a USB Connection

1. On the CLSS Gateway mainboard Side

Connect the USB-C side of the cable to the USB port of the CLSS Gateway mainboard.
The USB port is labeled as 8 in the figure

Figure C.2

2. On the Panel Side

In the MCC card on the panel:
Connect the USB-B side of the cable. Refer to the figure

Figure C.22

3. Power Connection

Connect the CLSS Gateway mainboard to a 24V DC external power source.

NOTE:

The external power supply must be dedicated and not shared with any other

devices.

NOTE:

The panel’s power supply to the CLSS Gateway mainboard must be 24V DC

power.

NOTE:

The external power supply must be dedicated and not shared with any other

devices.

NOTE:

The panel’s power supply to the CLSS Gateway mainboard must be 24V DC

power.

Содержание CGW-MB




























































































































































































Результаты поиска

Содержание CGW-MB

Отзывы:

Honeywell CGW-MB, Инструкция по установке и эксплуатации, Страница: 170 / 187

Результаты поиска

Содержание CGW-MB

Отзывы: