Honeywell CGW-MB Скачать руководство пользователя страница 162

Страница: 162 / 187

CGW-MB Installation and Users’ Manual | P/N:LS10248-000HW-E | REV.G | JUL/31/2022

161

Gamewell-FCI Panels

Connecting to the Panels

TB6 and RS-232 Connections

The pin connections are as below:

•

S3 Series Panel

At the TB3 terminal of the panel,

• Connect the +ve wire to the TB3-1 pin.
• Connect the -ve wire to the TB3-2 pin.

At the TB5 terminal of the panel,

• Connect the GND wire to the TB5-1 pin.
• Connect the TxD wire to the TB5-2 pin.
• Connect the SUPV wire to the TB5-3 pin.
• Connect the RxD wire to the TB5-4 pin.

Power Connection

On the CLSS Gateway mainboard Side
Ensure that the power cable is connected with the power port of the CLSS Gateway

mainboard.

The power port is labeled as 7 in the

Figure C.15

On the Panel Side

• Connect the Red wire to the +ve pin in the TB2 port.
• Connect the Black wire to the -ve pin in the TB2 port.

Содержание CGW-MB




























































































































































































Результаты поиска

Содержание CGW-MB

Отзывы:

Honeywell CGW-MB, Инструкция по установке и эксплуатации, Страница: 162 / 187

Результаты поиска

Содержание CGW-MB

Отзывы: