Honeywell CGW-MB Скачать руководство пользователя страница 142

Страница: 142 / 187

CGW-MB Installation and Users’ Manual | P/N:LS10248-000HW-E | REV.G | JUL/31/2022

141

ESSER Panels

Connecting to the Panels

C.4.2 To Use an RS 232 Connection

ESCOM Panels

Using an RS-232 cable the CGW-MB and the panel are connected.
The RS-232 port in the CLSS Gateway mainboard board is labeled as 6 in the

Figure C.2

On the CLSS Gateway mainboard Side

Connect to an RS-232 port of the CLSS Gateway mainboard board.

On the Panel Side

• Connect the White wire to the RxD+ pin.
• Connect the Brown wire to the TxD+ pin.
• Connect the Green wire to the 0V pin.

Figure C.4: Wiring Diagram: RS232 Connection for an ESCOM Panel

Power Connection

Using the RS 232 cable, the CLSS Gateway mainboard can connect to the 24V DC power
supply module of the ESCOM panel.

On the CLSS Gateway mainboard Side

• Connect the +ve wire to the +ve pin of the power supply port.
• Connect the -ve wire to the -ve pin of the power supply port.

On the Panel Side

• Connect the +ve wire to the +24 pin of the power supply module.
• Connect the -ve wire to the Gnd pin of the power supply module.

NOTE:

Use the details given on the power supply module of the panel.

NOTE:

The panel’s power supply to the CLSS Gateway mainboard must be 24V DC

power.

Содержание CGW-MB




























































































































































































Результаты поиска

Содержание CGW-MB

Отзывы:

Honeywell CGW-MB, Инструкция по установке и эксплуатации, Страница: 142 / 187

Результаты поиска

Содержание CGW-MB

Отзывы: