Honeywell CGW-MB Скачать руководство пользователя страница 116

Страница: 116 / 187

CGW-MB Installation and Users’ Manual | P/N:LS10248-000HW-E | REV.G | JUL/31/2022

115

Configuring the BACnet Network Settings

The BACnet Feature

8.9 Configuring the BACnet Network Settings

8.9.1 Installation and Configurations

The CGW-MB can communicate with the BACnet client in an Ethernet LAN.

8.9.2 The IP Settings

The following information applies to IP settings:
•

You can use only the

Eth1

port for connections to BACnet clients. For more details,

refer to

8.10.1 "To Configure the BACnet Settings"

•

Each CGW-MB is shipped with a default node number of 235.

•

The computer used to configure the CGW-MB must establish an IP connection to the

CLSS Gateway mainboard. Consult with a network administrator if unsure how to

make this connection.

•

Connecting more than one CGW-MB prior to reconfiguring the IP address will result in

an IP address conflict.

Содержание CGW-MB




























































































































































































Результаты поиска

Содержание CGW-MB

Отзывы:

Honeywell CGW-MB, Инструкция по установке и эксплуатации, Страница: 116 / 187

Результаты поиска

Содержание CGW-MB

Отзывы: