Honeywell C7735A1000 Скачать руководство пользователя страница 1

INSTALLATION INSTRUCTIONS

69-1521EFS-01

C7735A1000 Duct Air

Temperature Sensor

APPLICATION

The C7735A1000 Duct Air Temperature Sensor (DATS) 

is a duct-mounted temperature probe used to sense 

discharge air temperature in zoning applications for high 

and low temperature limit protection.  Alternatively, it is 

used with certain Honeywell thermostats for delta-T 

diagnostics and IAQ control.  For more on these 

applications, please see the installation instructions for 

those products.

Fig. 1. C7735A dimensions in in. (mm).

INSTALLATION

When Installing this Product...

1.

Read these instructions carefully. Failure to follow 

them could damage the product or cause a hazard-

ous condition. 

2.

Check the ratings given in the instructions and on 

the product to make sure the product is suitable for 

your application. 

3.

Installer must be a trained, experienced service 

technician.

4.

After completing installation, use these instructions 

to check out the product operation.

IMPORTANT

Do not locate the DATS probe in a duct near the 

heat exchanger or strip heat, which can cause 

false temperature readings.

1.

Assemble the DATS by attaching the metal sensor 

probe to the plastic cap. Insert the plate of the 

probe into the two tabs on the inside bottom of the 

cap. Then rotate the plate clockwise until it clicks 

into the single top tab.

2.

Locate the DATS on the supply trunk between the 

bypass damper and the evaporator coil and/or heat 

exchanger. If a bypass damper is not used, locate 

the DATS between the zone dampers and the 

evaporator coil and/or heat exchanger. See Fig. 2.

Fig. 2. DATS mounting location.

3.

Drill a 1/4 in. hole in the duct at the location 

selected for the sensor.

4.

Attach wire using wire nuts and push them into the 

cover, then insert the probe into the hole drilled in 

step 2.

5.

Secure the DATS to the side of the duct, through 

the two mounting holes, with the screws supplied.

IMPORTANT

Use 18-22 gauge thermostat wire for shorter 

runs. For longer runs or when wiring near volt-

age, use shielded cable.

6.

Run wire to zone panel or thermostat. See zone 

panel or thermostat installation instructions.

M33115

2-7/16 (62)

1-1/32

(26)

3-15/16 (100)

2-7/16

(62)

ZONE DAMPERS

BY PASS DAMPER

PLACE SENSOR 

INTHIS AREA.

DO NOT

PLACE

SENSOR IN

THIS AREA.

M14877A

EVAPORATOR COIL

HEAT EXCHANGER

BLOWER

Содержание C7735A1000









Отзывы: