ÊK14883-3V2FŠ
K14883-3V2 12/12 Rev. B
AVS Audio Verification System
QUICK GUIDE
This guide explains how to install the AVS PC board assembly in a VISTA series residential control cabinet when using the AVS
addressable mode. Please refer to the control’s Installation and Setup Guide and the instructions provided with this module for
detailed information, or if using a control not compatible with the AVS addressable mode.
Compatibility Note:
When using addressable mode, the AVS is intended to work with controls having the following firmware versions:
VISTA-20P series = version 7.0 or higher; VISTA-21iP series = version 3.0 or higher; VISTA-15P series = version 6.0 or higher.
1. MOUNT THE ASSEMBLY
Refer to the diagram at right.
a. Position the mounting plate/PC board assembly in the bottom of the control’s
cabinet.
b. Slide the mounting plate to the right so that the plate’s left-hand tang slides under
the cabinet’s tie-wrap loop.
c. Secure the assembly to the cabinet using the two self-tapping screws provided.
d. Mount the control’s PC board if not already mounted; follow the control’s instructions
for mounting the board (and optional RF Receiver board, if used).
BATTERY NOTE:
When using a 7AH battery, mount the battery vertically on the
bottom left-hand side of the cabinet, with the terminals facing down and right
(negative terminal closest to the PC board bracket).
2. MAKE THE AVS WIRING CONNECTIONS
Refer to the diagram below.
AVS to Panel Wiring
AVS-003-V0
SYSTEM
BATTERY
2
3
5
1
ON
4
2
3
1
ON
4
TANG
BENEATH
MOUNTING
PLATE
SECURE
WITH TWO (2)
SELF-TAP SCREWS
(SUPPLIED)
SLIDE ASSEMBLY TO RIGHT UNTIL
TANG SLIPS UNDER CABINET LOOP
CABINET
TIE-WRAP
LOOP
a.
ECP Connection:
IMPORTANT:
The AVS should be the
only device connected to the control’s
ECP terminals. Connect all other
control panel ECP devices to the AVS
ECP terminals. Make sure the current
drain of connected ECP devices does
not exceed the control’s maximum.
Using the red, black, green and yellow
wires of the supplied harness,
connect the ECP terminals from the
control (ground, aux, data in, data out)
to the
Panel
terminals on the AVS
base unit.
b.
Phone Connection:
(use a Direct Connect cord)
•
Connect red and green wires to the
control’s Incoming phone terminals.
•
Connect brown and gray wires to
the base unit’s
Handset
terminals.
•
Connect the control’s Handset
terminals to the base unit’s
Incoming
Phone Line
terminals.
AVS to Station Wiring
a. Mount the Station according to its
instructions.
b. Connect the base unit’s
AAV
terminals
to the station’s
AAV
terminals, routing
the wires through a cabinet knockout
and through the opening in the
station’s case or side cutout.
c. If connecting an adjacent keypad to
the station, connect the station’s
Keypad
header to the keypad’s
connection terminals.
AVS to GSMV4G/GSMX4G Module
Connection
a. If using a GSMV4G or GSMX4G
module for 2-way voice operation,
install the module according to its
instructions.
NOTE:
The module must
be mounted within 3 feet of the
control.
b. Connect the audio cable (not
supplied) from the GSMV4G or
GSMX4G module to the Audio
connector on the AVS board.
c. Complete all other GSMV4G/
GSMX4G wiring following the
instructions included with that module.
VISTA SERIES RESIDENTIAL CONTROL
BATTERY
HANDSET
(EAR
TH GND
(RING)
(TIP)
GR
Y
BRN
GRN
RED
INCOMING
PHONE LINE
(RING)
(TIP)
DIRECT
CONNECT
CORD
ECP TERMINALS
AVS-001-V2
AVS BASE UNIT
KEYPAD
BLK
GRN
YEL
RED
MIC
SPEAKERS
DATA
AUDIO
GND
+VDC
YEL
GRN
BLK
RED
AAV
AVST STATION
BRN
GRY
RING
TIP
RING
TIP
(200 FT
. MAX)
HANDSET
INCOMING
PHONE LINE
SUPPLIED HARNESS
GSMV-AUDIO CABLE (NOT SUPPLIED)
DATA
IN
DATA
OUT
PREMISES
PHONES
INCOMING
TELCO
RING
TIP
RING
TIP
KEYPAD
7
8
1
2
3
4
5
6
TRIGGER HEADER
RJ31X
1
2
3
4
5
6
7
8
RED BLK GRN YEL
RED BLK GRN YEL
RED BLK GRN YEL
PANEL
ECP
PHONE
AAV
TO ALL
OTHER ECP
DEVICES
LED
VOLUME / ID
BUTTON
LED
NORMAL MODE
PROGRAM MODE
CALLBACK MODE
PANEL TRIGGER
MODE
GND AUX
AUDIO CONNECTOR
IMPORTANT:
DO NOT CONNECT ANY OTHER
ECP DEVICES TO PANEL.
USE AVS BASE UNIT ECP
TERMINALS FOR OTHER ECP DEVICES.
NOT
USED
DIP SW
DEVICE ADDRESS
(ADDRESS 8
SHOWN)
GSMV4G/
GSMX4G
(OPTIONAL)
VISTA-20P/
VISTA-21iP = 11
BASE UNIT
DEVICE ADDRESS
VISTA-15P = 8
2
3
4
1
ON
2
3
5
4
1
ON
2
3
5
4
1
ON
2
3
5
4
1
ON
TB 1
6
7
8
5
11
10
9
2
3
4
1
NOTE:
The AVST Remote Station must be
mounted a minimum of 12 feet (3.7m)
from the AVS Base Station and the
GSMV4G module's antenna. Using the
AVST at less than the minimum spacing
may cause undesired noise at the AVST
Remote Station.
REMOTE STATION NOTE:
If using more than one remote station, an external power supply
must be used. Refer to the diagram in the Installation and Setup Guide for connection diagram.
Base Unit LED Functions
Steady On
base unit is powered; normal mode
Off
phone ringing for callback
Rapid Flash
Program mode: waiting for callback code entry
Slow Flash
2-Way Voice mode
Double Flash
Listen mode or Talk mode
(
CONTINUED ON OTHER SIDE
➙
)