Honeywell 60 Series Скачать руководство пользователя страница 38

Страница: 38 / 93

Honeywell 60 Series IP Camera Software Configuration Guide

Figure 4-6 Audio

Mute

: Check to disable audio transmission from the Network Camera to all clients.

Microphone source

: Select

Internal

External

from the dropdown list.

Note

The Internal microphone source is applicable for HC60W34R2 &
HC60W34R2L.

Internal microphone input gain

: Select the gain of the internal audio input according to

ambient conditions. Adjust the gain from 0% (least) to 100% (most).

Note

The Internal microphone input gain is applicable for HC60W34R2
& HC60W34R2L.

External microphone input gain

: Select the gain of the external audio input according to

ambient conditions. Adjust the gain from 0% (least) to 100% (most).

Audio type

: Select audio codec as G.711 or G.726 and the bit rate.

•

G.711 provides good sound quality and requires about 64Kbps. Select pcmu (

-Law) or

pcma (A-Law) mode.

•

G.726 is a speech codec standard covering voice transmission at rates of 16, 24, 32, and
40kbit/s.

After you complete the settings on this page, click

SAVE

to enable the settings.

Configuring IR Control Settings

Go to

Setup



Camera Setup



IR Control

On this page, you can turn on the IR illuminator and adjust the luminance of IR lights.

Содержание 60 Series






























































































Результаты поиска

Содержание 60 Series

Отзывы:

Похожие инструкции для 60 Series

Бренды по названию

Популярные бренды

Honeywell 60 Series, Руководство по настройке

Результаты поиска

Содержание 60 Series

Отзывы:

Похожие инструкции для 60 Series

Бренды по названию

Популярные бренды