+
5800MICRA transmitters
Dimensions Dowel Package
0.750" diameter (3/4")
Additional Info
Dowel Lid 0.850" diameter x 0.060" thick
Wire Antenna
8" x 1/8" flexible antenna
Fits Cavity Depth
0.330" depth (11/32")
Power Source
3.0V Lithium Coin Cell Battery CR1620
Temperature Range
10º to 120º F (-12º to 49º C)
Operating Gap
0.5"
Compatibility
Windows
All Vinyl Window Types, Wood Casement, Awning,
Double-Hung and Access
MOUNTING
(
See Figure 1
)
1. Mark the selected location for the transmitter on the frame of the window.
2. Mark the location for the magnet on the window sash, directly opposite the
transmitter location. Before drilling any holes, make sure that the successful
Go/No Go reception tests have been conducted as called for in the
5800MICRA transmitter section. (see page back.)
3. Drill a hole at the location marked for the transmitter (3/4" diameter, no
more than 11/32" deep).
4. Install the battery (observe polarity), then insert the transmitter into the
hole so that the cap is flush with the surface. Make sure the antenna goes
into the cavity as straight as possible.
DO NOT hammer the transmitter in place with hard blows. Press it into the
hole by hand.
The 5800MICRA uses a santaprene case that, once placed, is designed to
self-seal in the mounting hole. However, if desired, a thin bead of silicon
may be applied for additional moisture protection.
TOTHE INSTALLER
Regular maintenance and inspection (at least annually)
by the installer and frequent testing by the user are vital
to the continuous satisfactory operation of any alarm
system. The installer should assume the responsibility of
developing and offering a regular maintenance program
to the user, as well as acquainting the user with the proper
operation and limitations of the alarm system and its
component parts. Recommendations must be included for
a specific program of frequent testing (at least weekly) to
insure the system's operation at all times.
REFER TO THE lNSTALLATION INSTRUCTIONS FOR
THE RECEIVER / CONTROL WITH WHICH THIS DEVICE
IS USED FOR DETAILS REGARDING LIMITATIONS OF
THE ENTIRE ALARM SYSTEM.
FOR WARRANTY INFORMATION, PLEASE GO TO:
www.honeywell.com/security/hsc/resources/wa
BATTERY INSTALLATION & REPLACEMENT
Remove the transmitter from the window by inserting the flat blade of
a small screwdriver into the pry-slot on the cap end and twisting slightly
counter-clockwise. The transmitter must be removed from the window
completely in order to refit the transmitter properly back into the hole
once the internal battery has been replaced.
Using the flat blade of a small screwdriver in the pry-slot again, separate
the white cap from the base with a slight counter-clockwise twist.
Once open, slide the cap with the transmitter PC board assembly apart
from the base. Pull the antenna through the hole in the base just enough
to allow the battery to be replaced. Do not pull the antenna completely
out of the base.
Carefully remove the old battery from its battery holder on the bottom of the
PC board.
US Patent No. 6,737,969
800-07871 10/10 Rev. A
This device complies with FCC Rules part 15. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference that may be received, including interference that may
cause undesired operation.
The user shall not make any changes or modifications to the equipment unless authorized by the
Installation Instructions OR User Manual.
Unauthorized changes or modifications could void the user's authority to operate the equipment.
FCC
Notice
Figure 2. SPECIFICATIONS
Before drilling any holes, make sure that successful
Go/No Go transmission reception tests have been conducted as called for in the
5800MICRA transmitter section.
BATTERY CAUTION: Risk of fire, explosion and burns.
Do not recharge, disassemble, heat above 212"F (100"C) or incinerate. Dispose
of used batteries promptly. Keep away from children.
Reed Switch / Magnet Positioning
Ensure that orientation of the switch and magnet is the same.
Reed Switch on
top side of PC board
(inside cap)
STEP 1
STEP 2
STEP 3 & 4
STEP 5 & 6
STEP 7
Figure 3. Battery Replacement
5800MICRA
Recessed Transmitter
Ê800-07871X
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright © 2010 Honeywell International Inc.
5. Remove the adhesive backing on the magnet and place magnet at
marked location. Make sure magnet is placed in same orientation as
transmitter.
Magnet
Magnet
1.
2.
3.
Observe correct polarity (
see Figure 3, Step 3 & 4
) and insert the fresh battery
into the battery holder (positive polarity indicator is shown on the battery holder).
Slide the cap with the PC board assembly back into its base by gently pulling on
the antenna, easing the transmitter cap into place.
Snap the transmitter cap back onto the base, locking it into place.
Placing the antenna into the cavity first, reinsert the transmitter into its original
mounting hole in the window. Be sure to install the transmitter in the
same orientation as the accompanying sash-mounted magnet.
4.
5.
6.
7.
