Document 800-00789 – Rev C – 07/08
3 Inch Dome Camera
Quick Install Guide
FCC Compliance Statement
Information to the User: This equipment has been tested and found to comply with the limits for a
Class B digital device. Pursuant to Part 15 of the FCC Rules, these limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one of the following
measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment and receiver
•
Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected
•
Consult the dealer or a radio/TV technician for help.
Caution
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003.
Manufacturer’s Declaration of Conformance
The manufacturer declares that the equipment supplied with this guide is compliant with the essential
protection requirements of the EMC directive 89/336/EEC and the Low Voltage Directive LVD 73/23
EEC, conforming to the requirements of standards EN 55022 for emissions.
1 2 3 4 5 6 7 8
t
n
e
m
t
s
u
j
d
A
a
r
e
m
a
C
g
n
i
t
n
u
o
M
a
r
e
m
a
C
n
o
i
t
a
r
a
p
e
r
P
2. Connect the wiring
Surface Mount
Optional Camera Settings
1
2
3
1. Remove the dome cover
3. Prepare the mounting surface (surface or flush mount)
a.
Gently tu
r
n the dome cove
r
counte
r
-
clockwise to unlock, then pull f
r
ee of
the housing.
b.
Gently pull the inne
r
line
r
f
r
ee of the
two notches in the housing.
c.
Set the dome and line
r
aside.
a.
Connect the video output
connecto
r
.
b.
Connect the 24 VAC/12 VDC powe
r
connecto
r
.
24 VAC/12 VDC powe
r
connecto
r
Video output connecto
r
4S Electrical Junction Box
a.
Adapte
r
plate (optional). Secu
r
e to
elect
r
ical box using app
r
op
r
iate sc
r
ews
(not supplied).
b.
Secu
r
e came
r
a base to ceiling o
r
wall.
Adapte
r
plate
(optional)
Elect
r
ical box (not
supplied)
B
ase
a.
Ma
r
k the holes.
b.
Inse
r
t sc
r
ew ancho
r
s into
holes.
Flush Mount
a.
Adapte
r
plate (optional fo
r
ceiling tile).
Secu
r
e using app
r
op
r
iate sc
r
ews (not
supplied).
Su
r
face mount: Secu
r
e ski
r
t to ceiling o
r
wall
using _______ sc
r
ews supplied.
b.
Secu
r
e came
r
a base with ______________
sc
r
ews, supplied.
Ski
r
t
Adapte
r
plate
(optional)
a.
Tu
r
n the Axis
r
ing in the desi
r
ed
di
r
ection, then
r
etighten.
b.
Tu
r
n the Zoom leve
r
slightly
counte
r
-clockwise to loosen.
Then
r
otate a
r
ound the lens fo
r
the desi
r
ed image view.
c.
Tu
r
n the Focus leve
r
counte
r
-
clockwise to loosen. Rotate to
adjust fo
r
the best pictu
r
e
quality.
d.
Retighten the Zoom and Focus
leve
r
s to lock them afte
r
making adjustments.
Do not turn the lens more than 360°.
Do not use excessive force to loosen
the levers and axis ring.
Axis
r
ing
Focus
leve
r
Zoom
leve
r
Note
Please use the supplied DC I
r
is and Line Lock adjustment tool to adjust pictu
r
e
b
r
ightness and phase adjustment.
Picture Brightness
Use the LEVEL sc
r
ew to compensate fo
r
the i
r
is level. L (low) da
r
kens t
pictu
r
e. H (high) b
r
ightens the pictu
r
e.
Phase Adjustment
Use the V Phase Adjustment Pot to adjust the phase diffe
r
ence betwe e
came
r
as. Make su
r
e Switch 4 is ON to activate the Line lock function ( A
ope
r
ation only).
DIP Switches
Monito
r
out
Mode setting
DIP switches
Switch
Function
1
B
LC (
B
acklight Compensation). ON = came
r
a automatically
adjusts the exposu
r
e. OFF = facto
r
y default.
2
AGC (Automatic Gain Cont
r
ol). ON = came
r
a adjusts fo
r
low
light conditions. ON = facto
r
y default.
3
DC/AES Mode. Leave in ON position only.
4
LL (Line Lock). Set the came
r
a synch
r
onization to inte
r
nal o
r
Line lock (only available with 24 VAC). ON= facto
r
y default.
After mounting and adjusting
the camera, attach the dome
cover:
a.
Attach the inne
r
line
r
to the base until
the line
r
clicks into place.
b.
Align the dome cove
r
with the th
r
ee
dome tabs on the unit.
c.
Tu
r
n the dome gently clockwise until it
locks into place.
Preparation
Camera Mounting
Camera Adjustment
Installation Completion
1
2
3
4
Contents
Fully assembled camera
Hardware kit
Mounting template
This guide
Operating Notes
Warnings (where applicable to your locale)
Installation and servicing should be performed only by qualified and experienced technicians
to conform to all local codes and to maintain your warranty.
WARNING!
The use of CSA Certified/UL Listed Class 2 power adapters is required to
ensure compliance with electrical safety standards.
WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this product
(applicable in the European Union and other European countries with separate collection
systems). This product should be disposed of, at the end of its useful life, as per applicable local
laws, regulations, and procedures.
Power Supply
This dome camera can operate on 24 VAC or 12 VDC.
Operating Conditions
Avoid:
•
Viewing bright objects (for example, light fixtures) for extended
periods
•
Operating or storing the unit in the following locations.
•
Extremely humid, dusty, hot/cold environments (where the
operating temperature is outside the recommended range of
14°F to 122°F [-10°C to +50°C])
•
Close to sources of powerful electromagnetic radiation, such
as radio or TV transmitters
•
Close to fluorescent lamps or objects reflecting light
•
Under unstable light sources (may cause flickering)
Product Dimensions
Contact Information
4.9
”
(124.6 mm)
4.9
”
(124.6 mm)
4.1
7
”
(106.1 mm)
1.8
”
(46.0 mm)
+1.800.796.CCTV (North America only)
Document 800-00789 – Rev C – 07/08
© 2008 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without
written permission from Honeywell Video Systems. The information in this publication is believed to be accurate in all
respects. However, Honeywell Video Systems cannot assume responsibility for any consequences resulting from the use
thereof. The information contained herein is subject to change without notice. Revisions or new editions to this publication
may be issued to incorporate such changes.
2.03
”
(51.75 mm)
∅
3.97
”
(101 mm)
3.0
”
(76.2 mm)
0.9
”
(23.0 mm)
3.37
”
(85.5 mm)
1.68
”
(42.8 mm)
