manualshive.com logo in svg

Honeywell 145*g1D, Руководство пользователя, Страница: 51 / 206

Поделиться
Скачать
Honeywell 145*g1D Скачать руководство пользователя страница 51

3 - 9

Scanner Address

Scan the bar code below to determine the address of the scanner you are using.

Base or Access Point Address

Scan the bar code below to determine the address of the base or Access Point you are using.

Scanner Modes

Your scanner is capable of working in single scanner mode, multiple scanner mode, or with Bluetooth devices other than the 
charge base or Access Point.

Charge Only Mode

There may be times when you want to charge your scanner, but not link to the base.  For example, if a scanner is linked to 
an Access Point or other Bluetooth device and you need to charge the scanner, but want to retain your existing link.  

In order to program the base for Charge Only Mode, you must link a scanner to it.  Once the scanner is linked to the base, 
scan the 

Charge Only Mode 

bar code.  Any subsequent scanners placed in that base will charge without linking to it.  The 

scanner used to program the base remains linked to the base.  To unlink this scanner, scan 

Unlink Scanner

on page 3-10. 

Note: When in Charge Only Mode, the scanner periodically wakes up and beeps.  See "Power Up Beeper" on page 4-1 to 

change this setting.

If you want to charge a scanner and link to the base, use 

Charge and Link Mode

.  If the base is programmed for Charge 

Only Mode, you must link a scanner to it first in order to program it for Charge and Link Mode.  Scan the linking bar code on 
the base to link the scanner, then scan 

Charge and Link Mode

.  

Default = Charge and Link Mode.

 

Linked Modes

Locked Link Mode and Open Link Mode are the link modes that accommodate different applications.  Scan the appropriate 
bar codes included in the Open Link and Locked Link Mode explanations that follow to switch from one mode to another.  

Default = Open Link Mode

.

Scanner Address

Base Address

Charge Only Mode

* Charge and Link Mode

Содержание 145*g1D















































































































































































































Отзывы:

Нет отзывов