Honeywell 145*g1D Скачать руководство пользователя страница 36

Страница: 36 / 206

2 - 18

Turbo Mode:

The scanner sends characters to a terminal faster. If the terminal drops characters, do not use Turbo Mode.

Default = Off.

Numeric Keypad Mode:

Sends numeric characters as if entered from a numeric keypad.

Default = Off.

Automatic Direct Connect Mode:

This selection can be used if you have an IBM AT style terminal and the system is dropping

characters.

Default = Off.

RS232 Modifiers

RS232 Baud Rate

Baud Rate sends the data from the scanner to the terminal at the specified rate. The host terminal must be set for the

same baud rate as the scanner.

Default = 9600.

Turbo Mode On

* Turbo Mode Off

Numeric Keypad Mode On

* Numeric Keypad Mode Off

Automatic Direct Connect Mode

* Automatic Direct Connect

Mode Off

300

600

Содержание 145*g1D















































































































































































































Результаты поиска

Содержание 145*g1D

Отзывы:

Honeywell 145*g1D, Руководство пользователя, Страница: 36 / 206

Результаты поиска

Содержание 145*g1D

Отзывы: