Honeywell 145*g1D Скачать руководство пользователя страница 121

Страница: 121 / 206

7 - 19

UPC-A Addenda Required

When

Required

is scanned, the scanner will only read UPC-A bar codes that have addenda. You must then turn on a 2 or

5 digit addenda listed on

page 7-18

Default = Not Required.

UPC-A Addenda Separator

When this feature is on, there is a space between the data from the bar code and the data from the addenda. When turned

off, there is no space.

Default = On.

UPC-A/EAN-13 with Extended Coupon Code

Use the following codes to enable or disable UPC-A

and

EAN-13 with Extended Coupon Code. When left on the default setting

(

Off

), the scanner treats Coupon Codes and Extended Coupon Codes as single bar codes.

If you scan the

Allow Concatenation

code, when the scanner sees the coupon code and the extended coupon code in a single

scan, it transmits both as separate symbologies. Otherwise, it transmits the first coupon code it reads.

If you scan the

Require Concatenation

code, the scanner must see and read the coupon code and extended coupon code in a

single read to transmit the data. No data is output unless both codes are read.

Default = Off.

Required

* Not Required

* On

Off

* Off

Allow Concatenation

Require Concatenation

Содержание 145*g1D















































































































































































































Результаты поиска

Содержание 145*g1D

Отзывы:

Honeywell 145*g1D, Руководство пользователя, Страница: 121 / 206

Результаты поиска

Содержание 145*g1D

Отзывы: