Honda VFR1200F Скачать руководство пользователя страница 37

Страница: 37 / 143

Operation Guide

❙

Recommended Shift Points

Shifting Up

From 1st to 2nd

16 mph (25 km/h)

From 2nd to 3rd

22 mph (35 km/h)

From 3rd to 4th

28 mph (45 km/h)

From 4th to 5th

34 mph (55 km/h)

From 5th to 6th

37 mph (60 km/h)

Shifting Down

From 6th to 5th

34 mph (55 km/h)

From 5th to 4th

31 mph (50 km/h)

From 4th to 3rd

25 mph (40 km/h)

From 3rd to 2nd

19 mph (30 km/h)

From 2nd to 1st

12 mph (20 km/h)

NOTICE

Improper shifting can damage the engine, transmission,
and drive train. Also, coasting or towing the motorcycle
for long distances with the engine off can damage the
transmission.

VFR1200FD is equipped with an
automatically controlled 6-speed
transmission. It can be shifted automatically
(by AT MODE) or manually (by MT MODE).

If you put the motorcycle in gear with the
side stand down, the engine will shut off
with the clutch disengaged.

(VFR1200FD)

31MGE601.indb 35

2010/03/08 18:05:37

Содержание VFR1200F
















































































































































Результаты поиска

Содержание VFR1200F

Отзывы:

Бренды по названию

Популярные бренды

Honda VFR1200F, Руководство пользователя

Результаты поиска

Содержание VFR1200F

Отзывы:

Бренды по названию

Популярные бренды