Honda Super Cub 2019 Скачать руководство пользователя страница 54

Страница: 54 / 153

Storage Equipment

Helmet holder

The helmet holders are located under the

seat.

Use the helmet holders only when parked.

Seat Open

The seat open button can be operated when

the Honda SMART Key is in the operating

range (

P. 31) and the ignition switch is in

the OFF or (Lock) position.

Press the seat open button and open the

seat.

If the battery does not have enough voltage

to start the engine, the seat may not open.

Seat Close

Close the seat and push down on the rear of

the seat until it locks. Make sure that the seat

is locked securely to pull it up lightly.

WARNING

Riding with a helmet attached to the

holder can interfere with your ability to

safely operate the motorcycle and

could lead to a crash in which you can

be seriously hurt or killed.

Use the helmet holder only while

parked. Do not ride with a helmet

secured by the holder.

20181019183311_31K0GA000_enu_BOOK Page 55 Friday, October 19 2018 18:39:26 JST

Operation Guide

Helmet holders

Seat

Seat open button

Honda SMART Key

Содержание Super Cub 2019


























































































































































Результаты поиска

Содержание Super Cub 2019

Отзывы:

Похожие инструкции для Super Cub 2019

Бренды по названию

Популярные бренды

Honda Super Cub 2019, Руководство пользователя

Результаты поиска

Содержание Super Cub 2019

Отзывы:

Похожие инструкции для Super Cub 2019

Бренды по названию

Популярные бренды