Honda MSX125 2017 страница 68 Скачать руководство пользователя

Страница: 68 / 108

Clutch

Adjusting the Clutch Lever Freeplay

continued

Maintenance

Adjusting the Clutch Lever
Freeplay

❙

Upper Adjustment

Attempt adjustment with the upper clutch
cable adjuster first.

Pull back the rubber dust cover.

Loosen the upper lock nut.

Turn the upper clutch cable adjuster until
the freeplay is 10 to 20 mm (0.4 to 0.8 in).

Tighten the upper lock nut and check the
freeplay again.

Install the rubber dust cover.

❙

Lower Adjustment

If the upper clutch cable adjuster is threaded
out near its limit, or the correct freeplay
cannot be obtained, attempt adjustment
with the lower adjusting nut.

Upper lock nut

Upper clutch cable
adjuster

Rubber dust cover

–

17 MSX125 (LO CA)-32K26D200.book 63 ページ２０１７年２月１４日　火曜日　午前１０時２２分

Содержание MSX125 2017













































































































Результаты поиска

Содержание MSX125 2017

Отзывы:

Похожие инструкции для MSX125 2017

Бренды по названию

Популярные бренды

Honda MSX125 2017, Руководство пользователя

Результаты поиска

Содержание MSX125 2017

Отзывы:

Похожие инструкции для MSX125 2017

Бренды по названию

Популярные бренды