Honda HRX217VYAA Скачать руководство пользователя страница 12

Страница: 12 / 24

Blade Inspection

1. Turn the fuel valve OFF (

page 3

2. Disconnect the spark plug cap from the spark plug (

page 14

3. Tilt the mower to the right side so that the fuel cap side is up. This

will help to prevent fuel leakage and hard starting due to carburetor

flooding.

4. Inspect the blades for damage, cracks, and excessive rust or

corrosion.

A dull blade can be sharpened, but a blade that is excessively worn,

bent, cracked, heavily rusted, or otherwise damaged must be

replaced.

If a blade is bent, take the lawn mower to an authorized Honda

servicing dealer for inspection.

Blade Mounting Bolt Inspection

Inspect the blade bolts for any signs of damage

or looseness. If they are damaged, they must

be replaced.

Blade bolt torque:

36 ~ 43 ft-lb (49 ~ 59 N·m)

If they appear loose, a torque wrench must be

used to accurately tighten the blade bolts to the

required torque. If you do not have a torque

wrench, take your lawn mower to an authorized

dealer to have the bolts replaced or tightened.
Use only Honda Genuine blade bolts and

special washers, since they are specifically

designed for this purpose. Replacement part

numbers are on

page 20

Blade Replacement

1. Turn the fuel valve OFF (

page 3

2. Disconnect the spark plug cap from the spark plug (

page 14

3. Tilt the mower to the right side so that the fuel cap side is up. This

will help to prevent fuel leakage and hard starting due to carburetor

flooding.

4. Remove the two blade bolts with a 14 mm (6 point) socket wrench.

Use a wooden block to prevent the blades from turning when

removing the bolts. Remove the blades.

5. Clean dirt and grass from around the blade mounting area.
6. Install the sharpened or replacement blades using the two blade

bolts and special washers as shown below. Be sure to install the

washers in the direction shown.
Always install both blades as a set.

The blade bolts and washers are specially designed for this

application. When replacing bolts and washers, use only Honda

Genuine replacement parts.

7. Tighten the blade bolts with a torque wrench to the specified

torque. Use a wooden block to prevent the blades from turning

when tightening the bolts, as shown on

page 13

Blade bolt torque:

36 ~ 43 ft-lb (49 ~ 59 N·m)

If you do not have a torque wrench, have an authorized Honda

servicing dealer tighten the blade bolts.



WARNING

A worn, cracked, or damaged blade can break, and
pieces of the damaged blade can become dangerous
projectiles.

Blades thrown from the mower could seriously hurt or
kill someone.

Inspect the blades regularly, and do not operate the
mower with worn or damaged blades.

BLADE BOLTS

BLADES

NORMAL

WORN

BENT

CRACKED

NORMAL

TRAILING EDGE

EXCESSIVELY

WORN TRAILING

EDGE

Inspect washers and

bolt heads for

looseness and

damage.



WARNING

Operating the mower with only one blade will result in
an improperly seated blade that can become
dangerous projectiles.

Blades thrown from the mower could seriously hurt or

kill someone.
Always install both blades as a set.

UPPER BLADE

LOWER
BLADE

BLADE BOLT (2)

SPECIAL
WASHER (2)

BLADE BOLT [2]

AND WASHER [2]

SPECIAL WASHER
DIRECTION

UPPER BLADE

LOWER BLADE

Содержание HRX217VYAA

























Результаты поиска

Содержание HRX217VYAA

Отзывы:

Похожие инструкции для HRX217VYAA

Бренды по названию

Популярные бренды

Honda HRX217VYAA, Руководство пользователя

Результаты поиска

Содержание HRX217VYAA

Отзывы:

Похожие инструкции для HRX217VYAA

Бренды по названию

Популярные бренды