Honda HRR216VKA K10 Скачать руководство пользователя страница 58

Страница: 58 / 183

3-17

HRR216VKA

MAINTENANCE

17. GOVERNOR

MAXIMUM SPEED ADJUSTMENT

1. Loosen the governor arm nut on the governor arm.

2. Push the governor arm away from the carburetor to

open the carburetor throttle valve fully.

3. Hold the carburetor throttle valve fully open, and turn

the governor arm shaft clockwise fully. Tighten the
governor arm nut to the specified torque.

TORQUE:10 N•m (7 ft-lb)

4. Verify that the governor arm and the carburetor throttle

valve arm operate smoothly.

5. Start the engine and warm it up to the normal

operating temperature.

6. Have an assistant hold the flywheel brake lever while

you perform the maximum engine speed adjustment.

7. Check the maximum engine speed.

8. If adjustment is necessary, bend the governor spring

tab on the fuel valve plate very slightly.

• Left increases spring tension and engine speed.

• Right decreases spring tension and engine speed.



DANGER

The blades are rotating during this procedure.
The rotating blades will cause amputation if you
come in contact with the blades. Do not allow
your hands or feet to come into contact with the
rotating blades while performing this procedure.

Maximum speed

(no load)

K5 ~ K8

2,950 ~ 3,100 rpm

K9 ~ K11

2,950 ~ 3,050 rpm

GOVERNOR

SPRING

GOVERNOR ARM

GOVERNOR

ARM NUT

GOVERNOR

ARM SHAFT

FUEL VALVE

PLATE

BEND

INCREASE

SPEED

DECREASE

SPEED

GOVERNOR

SPRING TAB

SERVICE BULLETIN #106 =>

Содержание HRR216VKA K10
























































































































































































Результаты поиска

Содержание HRR216VKA K10

Отзывы:

Похожие инструкции для HRR216VKA K10

Бренды по названию

Популярные бренды

Honda HRR216VKA K10, Руководство пользователя

Результаты поиска

Содержание HRR216VKA K10

Отзывы:

Похожие инструкции для HRR216VKA K10

Бренды по названию

Популярные бренды