Honda HRR216VKA K10 Скачать руководство пользователя страница 57

Страница: 57 / 183

3-16

MAINTENANCE

HRR216VKA

16. REAR WHEEL ADJUSTER BUSHING

LUBRICATION

1. Drain the fuel and engine oil.

2. Put a protective pad around

the upper handle pipe. Turn
the lawn mower over. Tip it UP
and secure the upper handle
pipe in a vise.

3. Remove the rear wheel, pinion

gear, ratchet key and spring,
wheel cover, and all collars
and circlips from the
transmission axle.

4. (K5 thru K8 only): Remove the

rear scroll and drive belt
(

P. 4-2

), and then disconnect

the tension spring.

5. Remove the 22 mm circlip, and then slide the circlip

and the washer inward toward the transmission.

6. Remove the adjuster assembly, taking care not to

damage the seal.

7. Inspect the bushing and seals for wear and replace as

necessary.

8. Thoroughly clean the bushing contact areas on the

axle using a Scotch-Brite™ pad.

9. Thoroughly apply a coat of Honda Marine extreme

pressure NLGI #2 GC-LB grease or equivalent
INSIDE the adjuster arms and on the axle surfaces.

IMPORTANT:

Only use an extreme pressure NLGI #2 GC-LB wheel
bearing grease. Proper application of the correct
grease is critical to ensure proper operation.

DO NOT USE anti-seize, white lithium, silicon,
WD-40, or any other spray lubricant.

10. Reinstall the adjuster assembly and secure with the washer and circlip.

11. Reassemble the rear wheel in the reverse order of removal, applying grease as shown.

12. Perform this procedure for the other side.

FLAT WASHER

PINION GEAR

3 mm PINION GEAR

COLLAR (2)

13 mm CIRCLIP (2)

WHEEL BOLT

Install with the

punch mark

facing:

Left - inside

Right - outside

REAR WHEEL

RATCHET KEY



RATCHET

SPRING



AXLE

THRUST COLLAR

WHEEL

COVER

WHEEL WASHER

REASSEMBLY:

Install the washer as shown.

Install the curved wheel washer
in the direction shown.

FLAT WASHER



WASHER

CIRCLIP

ADJUSTER
ASSEMBLY



Clean bushing
contact areas with a
Scotch-Brite™ pad.

Содержание HRR216VKA K10
























































































































































































Результаты поиска

Содержание HRR216VKA K10

Отзывы:

Похожие инструкции для HRR216VKA K10

Бренды по названию

Популярные бренды

Honda HRR216VKA K10, Руководство пользователя

Результаты поиска

Содержание HRR216VKA K10

Отзывы:

Похожие инструкции для HRR216VKA K10

Бренды по названию

Популярные бренды