Honda HRR216VKA K10 Скачать руководство пользователя страница 52

Страница: 52 / 183

3-11

HRR216VKA

MAINTENANCE

12. FUEL TANK AND FILTER

FUEL TANK DRAINING AND CLEANING

1. Turn the fuel valve to the OFF position.

2. Loosen the carburetor bowl set bolt and drain the fuel

bowl into an approved container.

3. Turn the fuel valve to the ON position and allow the

remaining fuel in the tank to fully drain.

4. Slide the tube clip back on the fuel tube.

5. Rotate the fuel tube to help release the tube from the fuel

tank, and then pull the tube from the tank fitting.

NOTICE

Do not pry against the fuel tank with a screwdriver or
other tool, or the fuel tank may become damaged.

6. Remove the fuel filter from the fuel tube.

7. Inspect the fuel filter for sediment and other foreign

material. Inspect for tears or other damage.

8. Wash with solvent to clean, and dry thoroughly before

installation. Replace if necessary.

9. If the fuel filter is dirty, remove and clean the fuel tank

(

P. 8-23

10. Insert the fuel filter into the fuel tank fitting.

11. Connect the fuel tube to the fuel tank fitting.

12. Position the fuel tube clip over the fuel tank fitting.

13. After assembly, check for fuel leaks.



WARNING

Gasoline is highly flammable and explosive.
You can be burned or seriously injured when handling fuel.
•

Stop the engine and let it cool.

•

Keep heat, sparks, and flame away.

•

Handle fuel only outdoors.

•

Wipe up spills immediately.

FUEL TANK

FUEL FILTER

FUEL TUBE

TUBE CLIP

Содержание HRR216VKA K10
























































































































































































Результаты поиска

Содержание HRR216VKA K10

Отзывы:

Похожие инструкции для HRR216VKA K10

Бренды по названию

Популярные бренды

Honda HRR216VKA K10, Руководство пользователя

Результаты поиска

Содержание HRR216VKA K10

Отзывы:

Похожие инструкции для HRR216VKA K10

Бренды по названию

Популярные бренды