manualshive.com logo in svg

Honda HRR216VKA K10, Руководство пользователя

Поделиться
Скачать
Honda HRR216VKA K10 Скачать руководство пользователя страница 132

11-3

HRR216VKA

HANDLE PIPE/CABLES/SMART DRIVE

2. HANDLE STAY/DISCHARGE GUARD

REMOVAL/INSTALLATION

K5 ~ K9 Models

1. Pry the push nut off the discharge guard shaft.

2. Remove the discharge guard shaft, the left and right 

guard return springs, and the discharge guard.

Be careful when removing the discharge guard shaft. 
The guard return springs are under tension and can 
fly out and injure someone.

3. To replace the grass bag plate, remove the three 

grass bag plate bolts.

.

4. Release the handlebar locking knobs and allow the 

handle pipe assembly to rest on the floor.

5. Remove the two special bolts and nylon washers, 

and remove the handle pipe assembly from the 
handle stays.

PUSH NUT

GUARD 

RETURN 

SPRING (2)

DISCHARGE GUARD

GRASS BAG 

PLATE BOLT (3)

HANDLE LOCKING 

KNOB (2)

HANDLE STAY 

(left side shown)

SPECIAL 

BOLT (2)

NYLON WASHER (2)

HANDLE PIPE 

ASSEMBLY

Содержание HRR216VKA K10
























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды