manualshive.com logo in svg

Honda HRR216VKA K10, Руководство пользователя

Поделиться
Скачать
Honda HRR216VKA K10 Скачать руководство пользователя страница 118

10-9

HRR216VKA

CAM PULLEY/CRANKSHAFT/PISTON/ CYLINDER BLOCK

4. VALVES

DISASSEMBLY/REASSEMBLY

SPARK PLUG

INSPECTION: 

P. 3-9

Standard spark plug:
BPR5ES (NGK)

VALVE GUIDE

INSPECTION:

 

P. 10-20

CYLINDER BLOCK

CLEANING: 

P. 10-10

EXHAUST VALVE

REASSEMBLY:

Before installation, 
remove carbon deposits 
and inspect the valve.

INSPECTION:

 

P. 10-20

INTAKE VALVE

REASSEMBLY:

Do not interchange with the 
exhaust valve.

VALVE HEAD DIAMETER

IN: 25 mm (0.98 in)
EX: 24 mm (0.94 in)

INSPECTION: 

P. 10-20

VALVE SPRING (2)

INSPECTION: 

P. 10-20

VALVE SPRING RETAINER (2)

DISASSEMBLY:

Push down and slide the 
retainer to the side, so the 
valve stem slips through the 
hole at the side of the
retainer.

Do not remove the valve 
spring retainer while the piston 
is installed, or the valves will 
drop into the
cylinder.

VALVE STEM SEAL 

(INTAKE ONLY)

K9~K11 VERSIONS HAVE 

A ROUND INTAKE PORT

Содержание HRR216VKA K10
























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды