background image

2

COMPONENT & CONTROL LOCATION

BEFORE OPERATION CHECKS 

IS YOUR ENGINE READY TO GO?

For your safety, and to maximize the service life of your equipment, it 
is very important to take a few moments before you operate the engine 
to check its condition. Be sure to take care of any problem you find, or 
have your servicing dealer correct it, before you operate the engine.

Before beginning your preoperation checks, be sure the engine is level 
and the throttle lever (ignition switch lever or engine stop switch) is in 
the STOP position.

Always check the following items before you start the engine:

1. Fuel level (see page 5).

2. Oil level (see page 5).

The Oil Alert

®

 system (applicable engine types) will automatically 

stop the engine before the oil level falls below safe limits. However, 
to avoid the inconvenience of an unexpected shutdown, always 
check the engine oil level before startup.

3. Air cleaner (see page 6).

4. General inspection: Check for fluid leaks and loose or damaged 

parts.

5. Check the equipment powered by this engine.

Review the instructions provided with the equipment powered by 
this engine for any precautions and procedures that should be 
followed before engine startup.

OPERATION  

  

SAFE OPERATING PRECAUTIONS 

Before operating the engine for the first time, please review the 

SAFETY INFORMATION

 section on page 1 and the 

BEFORE 

OPERATION CHECKS 

above. 

Review the instructions provided with the equipment powered by this 
engine for any safety precautions that should be observed with engine 
startup, shutdown or operation.

TYPE 1: MANUAL THROTTLE / MANUAL CHOKE 

Starting A Cold Engine

1. Pull the choke rod to the 

CLOSED position.

STARTER 
GRIP

SPARK PLUG

OIL FILLER CAP/
DIPSTICK

MUFFLER

AIR 
CLEANER

FUEL 
TANK

THROTTLE 
LEVER (gray)

CHOKE ROD

MUFFLER 
DEFLECTOR
(optional)

IGNITION SWITCH 
LEVER (red)

Used on engines with a 
non-adjustable throttle 
lever.

Used on engines with 
an adjustable throttle 
lever.

ENGINE 
STOP 
SWITCH

CHOKE ROD

FUEL 
FILLER 
CAP

ENGINE CONTROL TYPES

OIL DRAIN 
BOLT

TYPE 1: MANUAL THROTTLE / MANUAL CHOKE

TYPE 2: FIXED THROTTLE /  IGNITION SWITCH LEVER / MANUAL CHOKE

TYPE 3: FIXED THROTTLE / ENGINE STOP SWITCH / MANUAL CHOKE

CHOKE ROD

WARNING

Improperly maintaining this engine, or failure to correct a 
problem before operation, can cause a malfunction in 
which you can be seriously hurt or killed.
Always perform a preoperation inspection before each 
operation, and correct any problem.

WARNING

Carbon monoxide gas is toxic. Breathing it can cause 
unconsciousness and even kill you.
Avoid any areas or actions that expose you to carbon 
monoxide.

CHOKE ROD

Содержание GC190

















Отзывы: