Honda EM5000SX Скачать руководство пользователя страница 76

Страница: 76 / 124

SERVICING YOUR GENERATOR

4. Remove the battery from the

battery tray.

This symbol on the battery means that this product must not be
treated as household waste.

An improperly disposed of battery can be harmful to the environment and
human health.
Always confirm local regulations for battery disposal.

Battery Charging

The battery is rated at 11.2 Ah (ampere-hours). Charging current should equal
10% of the battery’s ampere-hour rating. A battery charger should be used that
can be adjusted to deliver 1.1 amps.

Battery:

12 V 11.2 Ah (10 HR)

1. Connect the battery charger following the manufacturer’s instructions.

2. Charge the battery 5–10 hours.

3. Clean the outside of the battery and the battery tray compartment with a

solution of baking soda and water.

Battery Installation

1. Install the battery in the generator.

2. Connect the battery positive (+) cable to the battery positive (+) terminal first

and tighten the bolt securely.

3. Slide the battery boot over the positive (+) cable and terminal.

4. Connect the battery negative (–) cable to the battery negative (–) terminal,

and tighten the bolt securely.

BATTERY

31Z236200.book 74 ページ２０２０年２月２０日　木曜日　午後１時８分

Содержание EM5000SX





























































































































Результаты поиска

Содержание EM5000SX

Отзывы:

Бренды по названию

Популярные бренды

Honda EM5000SX, Руководство пользователя

Результаты поиска

Содержание EM5000SX

Отзывы:

Бренды по названию

Популярные бренды