manualshive.com logo in svg

Honda EM5000SX, Руководство пользователя

Поделиться
Скачать
Honda EM5000SX Скачать руководство пользователя страница 29

CONTROLS & FEATURES

27

RESTARTING THE ENGINE
When the engine is stopped automatically by CO-MINDER, press the CO-
MINDER reset button to restart the engine.
If the engine is restarted without pressing the CO-MINDER reset button, the 
engine will automatically stop immediately after restarting and the CO ALARM 
indicator will flash for approximately five minutes.
Resetting the CO-MINDER is possible only after the CO ALARM indicator is 
turned off.

CO-MINDER MALFUNCTION DETECTION
If the CO-MINDER detects a system malfunction, the engine will stop 
automatically and the FAULT/CO SENSOR LIFE indicator will flash for 
approximately five minutes. Press the CO-MINDER reset button to turn off the 
FAULT/CO SENSOR LIFE indicator. If the engine will not remain running after 
attempting to restart it and the FAULT/CO SENSOR LIFE indicator comes on 
again, there may be a system malfunction. If this occurs, do not attempt to 
restart the generator more than two times. If the CO-MINDER system is 
malfunctioning, it cannot warn you of potential high concentrations of carbon 
monoxide. Move the generator to a well-ventilated location and consult an 
authorized Honda Power Equipment dealer.

CO SENSOR LIFE
If the FAULT/CO SENSOR LIFE indicator flashes when operating the generator, 
the CO-MINDER may be reaching the end of its useful lifespan and will 
eventually need replacement.

• If the indicator flashes once every four seconds, this means there is 

approximately six months to one year of life left in the CO-MINDER.

• If the indicator flashes once every two seconds, this means there is 

approximately six months of life or less left in the CO-MINDER.

• The FAULT/CO SENSOR LIFE indicator indicates the estimated life left in the CO-

MINDER.

• The generator stopping period and storage period are also included in the useful 

lifespan of the CO-MINDER.

• Contact an authorized Honda Power Equipment dealer for CO-MINDER 

replacement.

31Z236200.book  27 ページ  ２０２０年２月２０日　木曜日　午後１時８分

Содержание EM5000SX





























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды