Honda EB10000 Скачать руководство пользователя страница 92

Страница: 92 / 120

TAKING CARE OF UNEXPECTED PROBLEMS

ENGINE LACKS POWER

NO POWER AT THE AC RECEPTACLES

Possible Cause

Correction

Air filter restricted.

Clean or replace air filter
(see pages 44, 68).

Bad fuel; generator stored without
treating or draining gasoline, or
refueled with bad gasoline.

Drain fuel tank and carburetor
(see page 83).
Refuel with fresh gasoline
(see page 19).

Fuel strainer restricted, carburetor
malfunction, ignition malfunction,
valves stuck, etc.

Take the generator to an authorized
Honda Power Equipment dealer, or
refer to the shop manual.

Possible Cause

Correction

AC circuit breaker left in the OFF
position after starting.

Check AC load and reset AC
circuit breaker (see page 59).

GFCI system activated.

• GFCI system

①

Test GFCI and reset AC circuit
breaker (see page 54).

• GFCI system

②

Test GFCI and press the GFCI RESET
button (see page 56).

• Replace or repair power tool or

appliance.

AC circuit protector tripped.

Check AC load and reset circuit
protector (see page 27).

Faulty power tool or appliance.

Replace or repair power tool or
appliance.
Stop and restart the engine.

Faulty generator.

Take the generator to an authorized
Honda Power Equipment dealer, or
refer to the shop manual.

31Z266200.book 90 ページ２０２０年２月２０日　木曜日　午前１１時１２分

Содержание EB10000

























































































































Результаты поиска

Содержание EB10000

Отзывы:

Бренды по названию

Популярные бренды

Honda EB10000, Руководство пользователя

Результаты поиска

Содержание EB10000

Отзывы:

Бренды по названию

Популярные бренды