Honda DS-2CC102P(N)-IRT Скачать руководство пользователя | Manualshive

Страница: 70 / 115

background image

68

STORAGE

STORAGE PREPARATION

Proper storage preparation is essential for keeping your generator
trouble-free and looking good. The following steps will help to keep rust
and corrosion from impairing your generator’s function and appearance,
and will make the engine easier to start when you use the generator
again.

Cleaning

Wipe the generator with a moist cloth. After the generator has dried,
touch up any damaged paint, and coat other areas that may rust with a
light film of oil.

Fuel

Depending on the region where you operate your equipment, fuel
formulations may deteriorate and oxidize rapidly. Fuel deterioration and
oxidation can occur in as little as 30 days and may cause damage to
the fuel system. Please check with your servicing dealer for local
storage recommendations.

Gasoline will oxidize and deteriorate in storage. Old gasoline will cause
hard starting, and it leaves gum deposits that clog the fuel system. If
the gasoline in your generator deteriorates during storage, you may
need to have the fuel system components serviced or replaced.
The length of time that gasoline can be left in your fuel tank without
causing functional problems will vary with such factors as gasoline
blend, your storage temperatures, and whether the fuel tank is partially
or completely filled. The air in a partially filled fuel tank promotes fuel
deterioration. Very warm storage temperatures accelerate fuel
deterioration. Fuel deterioration problems may occur within a few
months, or even less if the gasoline was not fresh when you filled the
fuel tank.

The

Distributor’s Limited Warranty

does not cover fuel system damage

or engine performance problems resulting from neglected storage
preparation.
You can extend fuel storage life by adding a gasoline stabilizer that is
formulated for that purpose, or you can avoid fuel deterioration
problems by draining the fuel tank.

31Z37613.book 68 ページ２０１５年１２月２日　水曜日　午前１０時４５分

«
...
68
69
70
71
72
...
»

Содержание DS-2CC102P(N)-IRT




















































































































Отзывы:

Нет отзывов

Похожие инструкции для DS-2CC102P(N)-IRT

Бренд: Harman Kardon Страницы: 6

Бренд: Harman Kardon Страницы: 16

ACS 600 MultiDrive

Бренд: ABB Страницы: 94

Бренд: Williams AV Страницы: 2

Бренд: Harman Kardon Страницы: 16

Hubner Berlin CANopen PMG 10

Бренд: Baumer Страницы: 28

Бренд: TRENDnet Страницы: 12

Бренд: HIKVISION Страницы: 50

Pocket Inverter 100

Бренд: XPower Страницы: 38

Бренд: Delta Страницы: 1

Бренд: Speaka Professional Страницы: 8

Бренд: G-Power America Страницы: 55

Бренд: INVT Страницы: 174

SC-TDC-1000 D Series

Бренд: Surface Concept Страницы: 28

Бренд: Cross Technologies Страницы: 18

NX Distributed Intelligence NX MEDIA CONVERTER

Бренд: Hubbell Страницы: 3

Бренд: Diodes Страницы: 5

VARIOMAT 2 Series

Бренд: Calpeda Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды