Honda DS-2CC102P(N)-IRT Скачать руководство пользователя страница 65

Страница: 65 / 115

SERVICING YOUR GENERATOR

BATTERY SERVICE

Your generator’s engine charging system charges the battery while the
engine is running. However, if the generator is only used periodically,
the battery must be charged monthly to maintain the battery service
life.

Emergency Procedures

Eyes

– Flush with water from a cup or other container for at least

fifteen minutes. (Water under pressure can damage the eye.)
Immediately call 911 (USA only) or a physician.

Skin

– Remove contaminated clothing. Flush the skin with large

quantities of water. Call a physician immediately.

Swallowing

– Drink water or milk. Call your local Poison Control Center

(USA only) or a physician immediately.

The battery contains sulfuric acid
(electrolyte), which is highly
corrosive and poisonous.

Getting electrolyte in your eyes or
on your skin can cause serious
burns.

Wear protective clothing and eye
protection when working near the
battery.

KEEP CHILDREN AWAY FROM THE
BATTERY.

31Z37613.book 63 ページ２０１５年１２月２日　水曜日　午前１０時４５分

Содержание DS-2CC102P(N)-IRT




















































































































Результаты поиска

Содержание DS-2CC102P(N)-IRT

Отзывы:

Похожие инструкции для DS-2CC102P(N)-IRT

Бренды по названию

Популярные бренды

Honda DS-2CC102P(N)-IRT, Руководство пользователя

Результаты поиска

Содержание DS-2CC102P(N)-IRT

Отзывы:

Похожие инструкции для DS-2CC102P(N)-IRT

Бренды по названию

Популярные бренды