Honda DS-2CC102P(N)-IRT Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 115

background image

47

OPERATION

ECO-THROTTLE SYSTEM

With the switch in the ON position, engine speed is automatically
lowered when loads are reduced, turned off, or disconnected. When
appliances are turned on or reconnected, the engine returns to the
proper speed to power the electrical load. In the OFF position, the
Eco-Throttle system does not operate.

Appliances with large start-up power demands may not allow the
engine to reach normal operating rpm when they are connected to the
generator. Turn the Eco-Throttle switch to the OFF position and
connect the appliance to the generator. If the engine still will not reach
normal operating speed, check that the appliance does not exceed the
rated load capacity of the generator.

If high electrical loads are connected simultaneously, turn the
Eco-Throttle switch to the OFF position to reduce voltage changes.

The Eco-Throttle system is not effective for use with appliances or
tools that require only momentary power. If the tool or appliance will
be turned ON and OFF quickly, the Eco-Throttle switch should be in the
OFF position.

ECO-THROTTLE SWITCH

OFF

ON

31Z37613.book 47 ページ２０１５年１２月２日　水曜日　午前１０時４５分

«
...
47
48
49
50
51
...
»

Содержание DS-2CC102P(N)-IRT




















































































































Отзывы:

Нет отзывов

Похожие инструкции для DS-2CC102P(N)-IRT

Бренд: XINDAK Страницы: 8

Бренд: La Marche Страницы: 15

Бренд: Cambridge Audio Страницы: 4

Бренд: Cambridge Audio Страницы: 2

Бренд: StarTech.com Страницы: 3

Бренд: e+p Elektrik Handels Страницы: 2

Бренд: Solplanet Страницы: 75

Бренд: Sincro Страницы: 84

Бренд: Generac Power Systems Страницы: 150

NX Distributed Intelligence NX MEDIA CONVERTER

Бренд: Hubbell Страницы: 3

Бренд: Monoprice Страницы: 4

Бренд: Cotek Страницы: 48

Бренд: Clarke Страницы: 12

Бренд: MyTek Страницы: 7

Бренд: Znshine Solar Страницы: 14

Бренд: ETarh Technology Страницы: 12

Бренд: HP Страницы: 16

Бренд: HP Страницы: 51

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды