Honda CTX700A страница 44 Скачать руководство пользователя

Страница: 44 / 141

n Gu

Riding in MT MODE

Shift up and down with the + and - switch.
The selected gear is shown on the gear
position indicator.

If the MT MODE is selected, the transmission
does not shift up automatically. Do not allow
the engine revs to go into the red zone.

The transmission automatically shifts down
when you slow down, even in MT MODE.

You will start from 1st gear even if MT MODE
is selected.

Gear shift operation

Shifting Up:
Press the shift up switch (+) (

Shifting Down:
Press the shift down switch (-) (

You cannot continue shifting gears by
keeping the shift switch pressed.
To continue shifting gears release the switch
and press it again.

Shift Limit

You cannot downshift if the engine will
exceed the rev limit.

14 CTX700-32MJF8000.book 41 ページ２０１３年５月９日　木曜日　午後９時５９分

Содержание CTX700A














































































































































Результаты поиска

Содержание CTX700A

Отзывы:

Похожие инструкции для CTX700A

Бренды по названию

Популярные бренды

Honda CTX700A, Руководство пользователя

Результаты поиска

Содержание CTX700A

Отзывы:

Похожие инструкции для CTX700A

Бренды по названию

Популярные бренды