Honda CBR650F 2014 Скачать руководство пользователя страница 39

Страница: 39 / 133

n Gu

Storage Equipment

The helmet holder, the helmet set wire (in the tool kit) and the tool kit are located under the
seat. There is also space to store a U-shaped lock.

The U-shaped lock is held in place above the
rear fender.

Use the helmet holder only when parked.

Some U-shaped locks may not fit in the
compartment due to their size or design.

Helmet holder

Helmet set wire

Tool kit

Helmet set wire

U-shaped lock

Helmet D-ring

WARNING

Riding with a helmet attached to the
holder can interfere with the rear
wheel or suspension and could cause a
crash in which you can be seriously
hurt or killed.

Use the helmet holder only while
parked. Do not ride with a helmet
secured by the holder.

Содержание CBR650F 2014






































































































































Результаты поиска

Содержание CBR650F 2014

Отзывы:

Похожие инструкции для CBR650F 2014

Бренды по названию

Популярные бренды

Honda CBR650F 2014, Руководство пользователя

Результаты поиска

Содержание CBR650F 2014

Отзывы:

Похожие инструкции для CBR650F 2014

Бренды по названию

Популярные бренды