manualshive.com logo in svg

Honda BF250A, Руководство пользователя, Страница: 50 / 139

Поделиться
Скачать
Honda BF250A Скачать руководство пользователя страница 50

48

OPERATION

During the warm-up period, check 

the oil pressure indicator (p. 33), 

overheat indicator (p. 33), and 

cooling system indicator (p. 34).

If the indicators show any 

abnormal condition, immediately 

stop the engine and determine the 

cause of the problem. Refer to 

TAKING CARE OF

 

UNEXPECTED PROBLEMS

 on 

p. 93.

6. If the fast idle control was used to 

warm-up the engine, gradually 

return the control lever to the N 

(neutral) position as the engine 

warms up.

STOPPING THE ENGINE

Emergency Engine Stopping

Side-Mount Type

To stop the engine in an emergency, 

pull the emergency stop switch clip 

out of the emergency stop switch by 

pulling the emergency stop switch 

lanyard.

We suggest that you stop the engine 

this way occasionally to verify that 

the engine and emergency stop switch 

are operating properly.

EMERGENCY

STOP SWITCH

EMERGENCY

STOP SWITCH

LANYARD

PULL

EMERGENCY

STOP SWITCH

CLIP

Panel-Mount/Top-Mount Types

EMERGENCY

STOP SWITCH

CONTROL PANEL

EMERGENCY

STOP SWITCH

LANYARD

PULL

EMERGENCY STOP

SWITCH CLIP

31ZX26040.book  Page 48  Friday, July 25, 2014  5:14 PM

Содержание BF250A












































































































































Отзывы:

Нет отзывов