manualshive.com logo in svg

Honda BF250A, Руководство пользователя, Страница: 43 / 139

Поделиться
Скачать
Honda BF250A Скачать руководство пользователя страница 43

41

OPERATION

3. Leave the fast idle lever in the 

OFF (fully lowered) position.

The fast idle lever cannot be raised 

unless the control lever is in the N 

(neutral) position.

The control lever cannot be moved 

away from the N (neutral) position 

unless the fast idle lever is lowered.

4. Turn the ignition switch key to the 

ON position; the buzzer will sound 

twice.

5. Turn the ignition switch key to the 

START position and hold it there 

until the engine starts.

When the engine starts, release the 

key, allowing it to return to the ON 

position.

If the engine fails to start within 5 

seconds, release the key and wait at 

least 10 seconds before operating 

the starter again.

• Using the electric starter for more 

than 5 seconds at a time will 

overheat the starter motor and can 

damage it.

• Turning the ignition switch key to 

the START position while the 

engine is running can damage the 

starter motor and flywheel.

LOWEST

POSITION

FAST IDLE LEVER

OFF

ON

START

IGNITION SWITCH KEY

31ZX26040.book  Page 41  Friday, July 25, 2014  5:14 PM

Содержание BF250A












































































































































Отзывы:

Нет отзывов