manualshive.com logo in svg

Honda BF250A, Руководство пользователя, Страница: 106 / 139

Поделиться
Скачать
Honda BF250A Скачать руководство пользователя страница 106

104

TAKING CARE OF UNEXPECTED PROBLEMS

SUBMERGED OUTBOARD 

MOTOR

A submerged outboard motor must be 

serviced immediately after it is 

recovered from the water in order to 

minimize corrosion.

If there is a Honda Marine dealership 

nearby, take the outboard motor to the 

dealer immediately. If you are far 

from a dealership, proceed as 

follows:

1. Remove the engine cover (p. 63), 

and rinse the outboard motor with 

fresh water to remove salt water, 

sand, mud, etc.

2. Drain the vapor separator as 

described on p. 88 – 89.

3. Change the engine oil and oil filter 

as described on p. 66 – 68. If there 

was water in the engine crankcase, 

or if the used engine oil showed 

signs of water contamination, then 

a second engine oil change should 

be performed after running the 

engine for half an hour.

4. Remove the spark plugs (p. 70). 

Operate the starter to expel water 

from the engine’s cylinder.

5. Put a teaspoon of engine oil into 

each spark plug hole to lubricate 

the inside of the cylinders. 

Reinstall the spark plugs.

If the engine was running when it 

submerged, there may be 

mechanical damage, such as bent 

connecting rods. If the engine binds 

when cranked, do not attempt to 

run the engine until it has been 

repaired.

31ZX26040.book  Page 104  Friday, July 25, 2014  5:14 PM

Содержание BF250A












































































































































Отзывы:

Нет отзывов