manualshive.com logo in svg

Honda BF100D, Руководство пользователя

Поделиться
Скачать
Honda BF100D Скачать руководство пользователя страница 41

39

CONTROLS AND FEATURES

OTHER FEATURES

Water Separator Buzzer

The water separator buzzer sounds a 
rapid, repeating signal when water 
has accumulated in the water 
separator.

Overrev Limiter

The engine is equipped with an 
overrev limiter to prevent the 
possibility of mechanical damage 
from excessive engine speed.

The overrev limiter may be activated 
during operation, limiting engine 
speed, if the outboard motor is 
trimmed or tilted up excessively, or 
when propeller ventilation occurs 
during a sharp turn.

If the overrev limiter is activated, 
check the trim angle of the outboard 
motor.

Check to see if the correct propeller is 
installed.

Portable Fuel Tank

(optional equipment)

The portable fuel tank has a capacity 
of 6.6 US gal (25 L) and has a fuel 
gauge built into the fuel tank 
connector.

WATER SEPARATOR

FUEL HOSE 

(standard equipment)

PORTABLE FUEL TANK

31ZY96300.book  39 ページ  ２０１３年１０月２１日　月曜日　午前９時２５分

Содержание BF100D




























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды