manualshive.com logo in svg

Honda BF100D, Руководство пользователя

Поделиться
Скачать
Honda BF100D Скачать руководство пользователя страница 121

119

TAKING CARE OF UNEXPECTED PROBLEMS

If overheating activates the engine 
protection system, idle the engine in 
neutral, and check the cooling system 
indicator.

If water is flowing from the cooling 
system indicator, continue idling for 
30 seconds. If the cooling system is 
OK, the overheat indicator should go 
off within 30 seconds, and the engine 
will respond normally to throttle 
control lever operation.

If there is no water flowing from the 
cooling system indicator, stop the 
engine, and tilt the outboard motor to 
inspect the water intake screens. If 
restricted, clean the water intake 
screens, return the outboard motor to 
the running position, restart the 
engine, and check the cooling system 
indicator again.

If there is still no water flowing from 
the cooling system indicator, or if the 
engine protection system remains 
activated after 30 seconds, return to 
the nearest boat landing, and have the 
outboard motor inspected by an 
authorized Honda Marine dealer.

WATER SEPARATOR 

BUZZER SOUNDS

When the water separator buzzer 
sounds (a rapid, repeating signal): 

Check the water separator for water 
contamination. If water is 
accumulated, stop the engine, and 
clean the water separator following 
the instructions on page 93, or consult 
with an authorized Honda Marine 
dealer.

COOLING SYSTEM INDICATOR

WATER SEPARATOR

31ZY96300.book  119 ページ  ２０１３年１０月２１日　月曜日　午前９時２５分

Содержание BF100D




























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды