Honda AQUATRAX R-12 страница 70 Скачать руководство пользователя

Страница: 70 / 252

Before Riding

Load Limits & Guidelines

Your PWC is primarily intended for
transporting you and a passenger.

Do not carry more cargo than the maximum
weight capacity allows.

Improperly loading your PWC can affect its
stability and handling.

Follow these guidelines whenever you carry a
passenger or cargo:

•

Do not place cargo on the seat, deck, or any
where else other than the storage
compartment or a glove box.

•

Do not attach any items to the handlebar.

Loading Guidelines

Overloading or improper loading can
make the personal watercraft difficult
to control and could result in an
accident.

Follow all load limits and other
loading guidelines in this manual.

Содержание AQUATRAX R-12





























































































































































































































































Результаты поиска

Содержание AQUATRAX R-12

Отзывы:

Похожие инструкции для AQUATRAX R-12

Бренды по названию

Популярные бренды

Honda AQUATRAX R-12, Руководство пользователя

Результаты поиска

Содержание AQUATRAX R-12

Отзывы:

Похожие инструкции для AQUATRAX R-12

Бренды по названию

Популярные бренды