manualshive.com logo in svg

Honda AQUATRAX R-12, Руководство пользователя

Поделиться
Скачать
Honda AQUATRAX R-12 Скачать руководство пользователя страница 210

Technical Information

202

Vehicle Identification

The registration (or primary) identification
number, hull identification number (HIN) ,
and engine number are required when you
register your PWC. They may also be
required when ordering replacement parts.
You may record these numbers in the 

Quick

Reference

section at the rear of this manual.

Also record these identification numbers with
your other important documents at home in
case your PWC is stolen.

Federal law requires that all PWC be
registered and numbered. The registration
number must appear on both sides of the
PWC, above the water line. Make sure the
numbering meets all local regulations.

The registration (or primary) identification
number (1) is located on both sides of the
PWC.

LEFT AND RIGHT SIDE

(1) registration identification number

Serial Numbers

(1)

Содержание AQUATRAX R-12





























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды