Honda AQUATRAX R-12 Скачать руководство пользователя страница 172

Страница: 172 / 252

Servicing Your Honda

164

Battery

6. Charge the battery (see following section),

unless you have been riding regularly.

7. Clean the top of the battery and the

terminals using a baking soda/water
solution.

8. Scrape off the deposits with a wire brush.
9. Rinse the battery with fresh water and dry

it.

10. Use waterproof grease to coat the

terminals.

11. Store your battery in an easy-to-reach

location off the floor, in an area protected
from freezing temperatures and direct
sunlight.

12. Clean the battery tray after removing the

battery for storage. Dry the battery tray
and, if paint is missing, re-paint the area.

13. Slow charge the battery (see following

section) once every 30 days.

Refer to

Safety Precautions

page 104

(1) “trickle” charger

Be sure to read the information that came
with your battery charger and follow the
instructions on the battery. Improper charging
may damage the battery.

Battery Charging

(1)

Содержание AQUATRAX R-12





























































































































































































































































Результаты поиска

Содержание AQUATRAX R-12

Отзывы:

Бренды по названию

Популярные бренды

Honda AQUATRAX R-12, Руководство пользователя

Результаты поиска

Содержание AQUATRAX R-12

Отзывы:

Бренды по названию

Популярные бренды