manualshive.com logo in svg

Honda AQUATRAX R-12, Руководство пользователя

Поделиться
Скачать
Honda AQUATRAX R-12 Скачать руководство пользователя страница 117

Servicing Your Honda

109

Maintenance Record

Keeping an accurate maintenance record will help ensure that your PWC is properly maintained.
Retain detailed receipts to verify the maintenance was performed. If the personal watercraft is sold,
these receipts should be transferred with the personal watercraft to the new owner.

Make sure whoever performs the maintenance completes this record. All scheduled maintenance,
including the 10 hours initial maintenance, is considered a normal owner operating cost and will be
charged for by your dealer. Use the space under Notes to record anything you want to remind
yourself about or mention to your dealer.

Hourmeter

Date

Performed By:

Notes

100 or 6

200 or 12

300 or 18

400 or 24

500 or 30

700 or 42

800 or 48

900 or 54

1000 or 60

600 or 36

Hours

or Months

Содержание AQUATRAX R-12





























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды