background image

 

14 

 

NOTICE: Fuel can damage paint and some types of plastic. Be careful not to spill fuel when filling your fuel 
tank. Damage caused by spilled fuel is not covered under the distributor’s warranty.  
Never use stale or contaminated petrol or oil/petrol mixture. Avoid getting dirt or water in the fuel tank. 
1.

 

Check the fuel level by looking through the translucent fuel 
tank.  

2.

 

If the fuel level is low, refuel in a well-ventilated area with the 
engine stopped. If the engine has been running, allow it to 
cool. 

To refuel, rest the engine a level surface with the fuel filler cap facing 
up (FIG. 5). Remove the fuel filler cap and fill the tank with petrol to 
the bottom of the filler neck. 
Refuel carefully to avoid spilling fuel. Do not overfill. There should be 
no fuel in the filler neck. After refueling, tighten the fuel filler cap 
securely. 
Keep petrol away from appliance pilot lights, barbecues, electric appliances, power tools, etc. 
Spilled fuel is not only a fire hazard. It causes environmental damage. Wipe up spills immediately. 

 

6.5

 

 ENGINE OIL 

Oil is a major factor affecting performance and service life. Use 4-stroke auto motive detergent oil.  
RECOMMENDED OIL 
Use 4-stroke motor oil that meets or exceeds the requirements for API service classification SJ or later (or 
equivalent).  
Always check the API service label on the oil container to be sure it includes the letters SJ or later (or 
equivalent). 
SAE 10W-30 is recommended for general use. The recommended operating range of this engine is 5°C to 
40°C (41°F to 104°F).   
 

6.6

 

OIL LEVEL CHECK (FIG. 6) 

Check the engine oil level before each use or every 10 hours if 
operated continuously.   
Check the engine oil level with the engine stopped and in a level 
position.  
1.

 

Remove the oil filler cap/dipstick and wipe it clean.  

2.

 

Insert and remove the oil filler cap/dipstick without screwing 
it into the oil filter neck, then remove it to check the oil level 
shown on the dipstick.  

3.

 

If the oil level is near or below the lower limit marked on the dipstick, fill to the bottom edge of the 
oil fill hole with the recommended oil. To avoid overfilling or under filling, be sure the engine is in a 
level position, as shown, while adding oil. 

4.

 

Reinstall the oil filler cap/dipstick and tighten securely.  

RUNNING THE ENGINE WITH A LOW OIL LEVEL CAN CAUSE ENGINE DAMAGE.  
THIS TYPE OF DAMAGE IS NOT COVERED BY THE DISTRIBUTOR’S LIMITED WARRANTY.  
 
 
 

 

 

Содержание 11985





















Отзывы: