HONDA marine BF25D Скачать руководство пользователя страница 49

Страница: 49 / 141

OPERATION

STARTING THE ENGINE

SHG and LHG Types

(long tiller handle)

1. Put the emergency stop switch clip

in the emergency stop switch, and

attach the emergency stop switch

lanyard securely to the operator or

to the operator’s PFD (Personal

Flotation Device).

The engine will not start or run unless

the emergency stop switch clip is in

the emergency stop switch.

The emergency stop switch clip and

emergency stop switch lanyard

system is a safety device that will

stop the engine if you fall away from

the controls while operating the boat.

Always attach the emergency stop

switch lanyard securely to the

operator or to the operator’s PFD

before starting the engine.

Before leaving the dock, check the

operation of the emergency stop

switch.

2. Check the position of the gearshift

lever. It must be in the N (neutral)

position for starting.

The engine will not start if the

gearshift lever is in the F

(forward) or R (reverse) position.

EMERGENCY STOP SWITCH

EMERGENCY STOP

SWITCH CLIP

EMERGENCY STOP

SWITCH LANYARD

N (neutral)

GEARSHIFT LEVER

31ZW26430.book Page 47 Monday, November 19, 2018 4:42 PM

Содержание BF25D












































































































































Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды

HONDA marine BF25D, Руководство пользователя

Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды