HONDA marine BF25D Скачать руководство пользователя страница 27

Страница: 27 / 141

CONTROLS AND FEATURES

Gearshift/Throttle Control Lever

The gearshift/throttle control lever

automatically locks itself in the N

(neutral) position. To move the lever

out of the N (neutral) position, you

must squeeze the neutral release lever

on the underside of the lever handle.

The gearshift/throttle control lever

controls engine speed and selects F

(forward), N (neutral), or R (reverse)

gears.

Moving the control lever 32° from N

(neutral) selects the gear, and further

movement increases engine speed.

A friction adjuster adjusts the

operating resistance of the control

lever (p. 57).

Less friction allows easier control

lever movement. More friction helps

to hold a steady throttle setting while

cruising.

GEARSHIFT/THROTTLE

CONTROL LEVER

NEUTRAL

RELEASE

LEVER

F (forward)

N (neutral)

R (reverse)

ENGINE

SPEED

HIGH

ENGINE

SPEED

32°

GEARSHIFT/THROTTLE

CONTROL LEVER

31ZW26430.book Page 25 Monday, November 19, 2018 4:42 PM

Содержание BF25D












































































































































Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды

HONDA marine BF25D, Руководство пользователя

Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды