Home Decorators Collection BECKFORD Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 16

Home Decorators Collection BECKFORD Скачать руководство пользователя страница 7

Please contact 1-800-986-3460 for further assistance.

HOMEDEPOT.COM/HOMEDECORATORS

7

Assembly

1

Preparing the canopy

3

Assembling the fan

WARNING:

Failure to properly install the cotter pin (FF) could

result in the fan loosening and possibly falling.

NOTE:

If a longer downrod (not included) is needed, take out

the screw located in the hanger ball (JJ), lower the hanger ball
(JJ) and remove the cross pin (KK). Remove all three pieces from
the downrod (LL) and assemble them onto the new longer
downrod before proceeding to the downrod installation. Be sure
to snap together the 3-PIN connectors, the male plug (MM)
from the fan and female plug from the extension cord (DD).

Loosen the two setscrews (HH) on the motor collar to allow

the downrod (LL) to be threaded in to.

Carefully feed the motor wires up through the downrod (LL).

Thread the downrod (LL) into the collar.

Align the holes and replace clevis pin (GG) and cotter pin

(FF). Tighten the two collar setscrews (HH).

Slip the coupling cover (E), canopy bottom cover (C) and

canopy (B) onto the downrod (LL).

Preparing the motor

2

Remove the cotter pin (FF) and clevis pin (GG), and loosen
the two collar setscrews (HH) from the motor collar.

Loosen setscrew (II) located in the hanger ball (JJ), lower the
hanger ball (JJ) and remove the cross pin (KK). Remove the
hanger ball (JJ) from the hanger ball/downrod assembly (D).

Carefully reinstall the hanger ball (JJ) onto the downrod (LL).
Ensure that the cross pin (KK) is in the correct position, the
setscrew (II) is tightened and wires are not twisted.

Remove the canopy bottom cover (C) from the canopy (B) by
turning the canopy bottom cover (C) counterclockwise.

Remove the mounting bracket (A) from the canopy (B) by
removing the non-slotted canopy mounting screw (EE) from
the bottom of the canopy (B) and loosening the slotted canopy
mounting screw (EE) a half turn from the screw head. Next,
turn the canopy (B) counterclockwise to remove the mounting
bracket (A) from the canopy (B).

EE

A

B

C

EE

II

D

KK

FF

GG

HH

HH

JJ

C

F

E

B

HH

HH

GG

FF

II

KK

DD

MM

LL

JJ

«
...
5
6
7
8
9
...
»

Содержание BECKFORD

















Отзывы:

Нет отзывов