SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY
INSTRUCTIONS
ReAd And foLLoW ALL
SAfeTY InSTRuCTIonS
Safety Information
Assembly Instructions
Storage
Shaping Instructions
Limited Warranty
Christmas Tree
Sku # 1000047798
• This seasonal use product is not intended for permanent
installation or use.
• Do not mount or place near gas or electric heaters, fireplaces,
candles or other similar sources of heat.
• Do not secure the wiring of the product with staples or nails, or
place on sharp hooks or nails.
• Unplug the product when leaving the house, when retiring for the
night, or if left unattended.
• Do not let lamps rest on the supply cord or any wire.
• Do not use this product for other than its intended use.
• Read and follow all instructions that are on, or provided with, the
product.
1. Unfold the tree stand and
insert the eye bolt. Remove
packing material from ends of
poles. Put bottom section pole
into tree stand making sure it
is seated properly (Figure 1).
Tighten eye bolt until bottom
section is held securely.
2. Insert the middle section of
the tree into the bottom
section (Figure 2)
3. Insert the rod of the top tree
section into the green plastic
opening (pole cap) of the
middle section. (Figure 3).
This tree is for indoor use only.
Retain carton for storage purpose.
Fig. 4
Fig. 1
Fig. 2
Fig. 3
Shaping the tree branches is the
last step of assembly. The care and
attention given to this final process
will result in a genuinely beautiful
and appealing holiday centerpiece.
1. Every tree style is shipped from
the factory with the tips of each
branch compressed to the center
(Fig. 1).
2. Each branch tip must be shaped
to it’s proper position to give the
tree a natural look. This is done by
gently grasping the left and right
wing tips and spreading them out
away from the center tip (Fig. 2).
3. Each individual tip should then be
spread out separately. Tips should
then be bent slightly upward to
add a more natural looking
appearance. Fig. 3 shows a
typical tree branch after shaping.
4. As you shape closer to the top,
the branches will not have wing
tips, but will otherwise shape in
the same manner as lower
sections.
New product registration can only be completed online at
www.nationaltree.com.
SAVE YOUR SALES RECEIPT. It will be needed
when requesting warranty service.
Please read this warranty thoroughly and familiarize
yourself with its restrictions and requirements.
National Tree Company warrants its 6.5 ft. and taller
trees against
manufacturer-only defects for a
period of five (5) years from the date of purchase
indicated on your sales receipt
. (White Trees,
one year).
Manufactured defective parts will be repaired or
replaced.
The lights on Pre-Lit Trees are warranted for
a period
of two (2) years from date of purchase; three (3)
years for low voltage LED trees
(see below).
This Warranty does not apply to trees that are used as
display trees in the store. This tree is for indoor use
only. Outdoor use of this tree voids the warranty. This
warranty is only valid on purchases made from
authorized NTC retailers.
PRE-LIT TREES LIMITED WARRANTY
National Tree Company warrants the light sets on its
Pre-Lit trees against
manufacturer-only defects in
material or workmanship for a period of two (2)
years from date of purchase; three (3) years for
low voltage LED trees.
Culpability of Company is
limited to replacement of defective light set only.
To have the Warranty placed into effect, completed
online registration of product is required with
inclusion of sales receipt noting purchase date
and place.
New product registration can only be
completed online at www.nationaltree.com.
Shipping Costs under PRE-LIT WARRANTY
TERMS:
Please note the following terms regarding
shipping of product for warranty service:
1) National Tree Company will pay the cost of shipping
(to our facility and back to customer), under warranty
terms, during the
first season
of use.
Receipt dated
prior to December 25 of purchase year constitutes first
season of use.
Please note that it is the responsibility
of the customer to obtain a box of the smallest
possible size and shape to securely contain the part
being shipped.
2) After the
second season
of use, the customer will
be responsible for cost of delivery to our facility.
National Tree Company will pay the return cost
delivery of parts repaired due to manufacturing defect.
Customer will be responsible for return shipping cost
of any parts repaired due to misuse or neglect.
3) All shipping costs to and from our facility for
warranty service after the
third season
of use will be
the responsibility of the customer.
REQUIREMENTS FOR WARRANTY SERVICE:
Customers are required to contact National Tree
Company for AUTHORIZATION OF RETURN prior to
shipping product for warranty service.
To receive authorization of return, email us at
service@ nationaltree.com or call 1-888-494-PART
(7278). Information required will include: product item
number, UPC bar code number, name of store where
purchased, a detailed description of the problem, and
your address and phone number.
At the discretion of National Tree Company, you may
either receive a replacement part or be instructed as
to which part(s) to ship prepaid to National Tree for our
inspection and determination and/or possible repair.
Replacement or repair as provided by this limited
warranty is our exclusive remedy to the consumer and
does not place National Tree Company liable for any
incidental or consequential damages.
IMPORTANT NOTES:
Removing factory attached functioning or non-
functioning light strings from any section of your
pre-lit tree will
void the warranty
.
Please retain the product carton for storage purposes
and/or for use in the event of warranty service for
product shipment.
Keep product away from heat and moisture. This
limited warranty does not cover damage resulting
from accident, misuse, abuse, negligence, or normal
wear. In these instances, parts can be purchased at a
reasonable fee plus shipping charges.
RETAIN FOR YOUR RECORDS
Tree Style No.
UPC Code
Store Where Purchased
Date Purchased
Price
Gently press tips back into center branch. Raise all branches to
original upright position taking care not to place undue pressure on
the attached ends of the branches. When disassembling tree, a
twisting motion will help to separate the sections from each other.
All tree parts can be replaced in carton and should be stored in a
cool, dry place.
Fig. 1
Fig. 2
Fig. 3
4. SHAPING: Working your way
up from the bottom, gently
lower all branches from their
upright setting (Figure 4).
Each branch must be shaped
to a natural position by
spreading out the left and right
tips away from the center tip
(See Shaping Instructions).
Continue to lower branches
on upper section in the same
manner making sure not to
place undue pressure on the
brackets.
