Holtek HT46R47 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 77

background image

HT46R48A

Pin Name I/O Configuration

Option

Description

PA0~PA2
PA3/PFD
PA4/TMR
PA5/INT
PA6~PA7

I/O

Pull-high

Wake-up

PA3 or PFD

Bidirectional 8-bit input/output port. Each individual pin on this port can be config-
ured as a wake-up input by a configuration option. Software instructions determine
if the pin is a CMOS output or Schmitt Trigger input. Configuration options deter-
mine which pins on the port have pull-high resistors. Pins PA3, PA4 and PA5 are
pin-shared with PFD, TMR and INT, respectively.

PB0/AN0
PB1/AN1
PB2/AN2
PB3/AN3
PB4~PB7

I/O

Pull-high

Bidirectional 8-bit input/output port. Software instructions determine if the pin is a
CMOS output or Schmitt Trigger input. Configuration options determine which pins
on the port have pull-high resistors. PB is pin-shared with the A/D input pins. The
A/D inputs are selected via software instructions. Once selected as an A/D input,
the I/O function and pull-high resistor options are disabled automatically.

PC0~PC1

I/O

Pull-high

Bidirectional 2-bit input/output port. Software instructions determine if the pin is a
CMOS output or Schmitt Trigger input. Configuration options determine which pins
on the port have pull-high resistors.

PD0/PWM I/O

Pull-high

I/O or PWM

Bidirectional 1-bit input/output port. Software instructions determine if the pin is a
CMOS output or Schmitt Trigger input. Configuration option determines if this pin
has a pull-high resistor. The PWM output is pin-shared with pin PD0 selected via a
configuration option.

OSC1
OSC2

I

O

Crystal or RC

OSC1, OSC2 are connected to an external RC network or external crystal, deter-
mined by configuration option, for the internal system clock. If the RC system clock
option is selected, pin OSC2 can be used to measure the system clock at 1/4 fre-
quency.

RES

I

¾

Schmitt Trigger reset input. Active low.

VDD

¾

¾

Positive power supply

VSS

¾

¾

Negative power supply, ground

Note:

1. Each pin on PA can be programmed through a configuration option to have a wake-up function.
2. Individual pins can be selected to have a pull-high resistor.
3. Pins PB4~PB7 exist but are not bonded out on the 20-pin package.
4. Unbonded pins should be setup as outputs or as inputs with pull-high resistors to conserve power.

HT46R46/C46/R47/C47/R48A/C48A/R49

Rev. 1.41

4

December 30, 2008

«
...
2
3
4
5
6
...
»

Содержание HT46R47














































































Отзывы:

Нет отзывов

Похожие инструкции для HT46R47

Бренд: Lawler Страницы: 2

Бренд: QUAD Страницы: 17

Бренд: fadini Страницы: 16

Бренд: VAT Страницы: 26

Бренд: Parker Страницы: 44

Бренд: K1EL Страницы: 46

Бренд: ZIGBEE Страницы: 5

Бренд: L-Acoustics Страницы: 24

Бренд: L-Acoustics Страницы: 21

Бренд: M&S Systems Страницы: 4

Бренд: Matelec Страницы: 16

Бренд: IBM Страницы: 214

Бренд: STIEBEL ELTRON Страницы: 44

Бренд: Burlington Страницы: 7

CentralControl CC41

Бренд: Becker Страницы: 48

Бренд: GSK Страницы: 32

Бренд: Nice Страницы: 32

Бренд: Rational Страницы: 140

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды