manualshive.com logo in svg

Holtek HT32F50231, Руководство пользователя, Страница: 345 / 486

Поделиться
Скачать
Holtek HT32F50231 Скачать руководство пользователя страница 345

Rev. 1.00 

345 of 486

July 31, 2018

32-Bit Arm

®

 Cortex

®

-M0+ MCU

HT32F50231/HT32F50241

16  Motor Control T

imer (MCTM)

Channel 0 Output Configuration Register – CH0OCFR

This register specifies the channel 0 output mode configuration.

Offset:

0x040 

Reset value: 0x0000_0000

31

30

29

28

27

26

25

24

Reserved

Type/Reset

23

22

21

20

19

18

17

16

Reserved

Type/Reset

15

14

13

12

11

10

9

8

Reserved

CH0OM[3]

Type/Reset

RW 0

7

6

5

4

3

2

1

0

Reserved CH0IMAE CH0PRE

Reserved

CH0OM[2:0]

Type/Reset

RW 0 RW 0

RW 0 RW 0 RW 0

Bits

Field

Descriptions

[5]

CH0IMAE

Channel 0 Immediate Active Enable

0: No action

1: Single pulse Immediate Active Mode is enabled

The CH0OREF will be forced to the compare matched level immediately after 
an available trigger event occurs irrespective of the result of the comparison 
between the CNTR and the CH0CCR values.
The effective duration ends automatically at the next overflow or underflow 
event.

Note: The CH0IMAE bit is available only if channel 0 is configured operate in PWM 

mode 1 or PWM mode 2.

[4]

CH0PRE

Channel 0 Capture/Compare Register (CH0CCR) Preload Enable

0: CH0CCR preload function is disabled

The CH0CCR register can be immediately assigned a new value when 
the CH0PRE bit is cleared to 0 and the updated CH0CCR value is used 
immediately.

1: CH0CCR preload function is enabled

The new CH0CCR value will not be transferred to its shadow register until an 
update event 1 occurs.

Содержание HT32F50231







































































































































































































































































































































































































































































































Отзывы:

Нет отзывов