manualshive.com logo in svg

Holtek HT32F50231, Руководство пользователя, Страница: 167 / 486

Поделиться
Скачать
Holtek HT32F50231 Скачать руководство пользователя страница 167

Rev. 1.00 

167 of 486

July 31, 2018

32-Bit Arm

®

 Cortex

®

-M0+ MCU

HT32F50231/HT32F50241

12  
Analog to Digital Converter (ADC)

Sampling Time Setting

The conversion channel can be programmed the sampling time according to the input resistance of 

the input voltage source. This sampling time must be enough for the input voltage source to charge 

the internal sample and hold capacitor of the converter to the input voltage level. By modifying 

the ADST [7:0] bits in the ADCSTR register, the sampling time of the analog input signal can be 

determined.

The total conversion time (T

conv

) is calculated using the following formula:

T

conv

 = T

Sampling

 + T

Latency

Where the minimum sampling time T

Sampling

 = 1.5 cycles (when ADST[7:0] = 0) and the minimum 

channel conversion latency T

Latency

 = 12.5 cycles.

Example:

With the A/D Converter clock CK_ADC = 14 MHz and a sampling time = 1.5 cycles:

T

conv

 = 1.5 + 12.5 = 14 cycles = 1 μs

Data Format

The ADC conversed result can be read in the ADCDR register and output data format which is 

shown as following Table 24.

Table 24.  Data Format in ADCDR [15:0]

Description

ADCDR Register Data Format

Right aligned

“0_0_0_0_d11_d10_d9_d8_d7_d6_d5_d4_d3_d2_d1_d0”

Analog Watchdog

The A/D converter includes a watchdog function to monitor the converted data. There are two 

kinds of thresholds for the watchdog monitor function, known as the watchdog lower threshold 

and watchdog upper threshold, which are specified by the ADLT bit field and ADUT bit field in the 

ADCTR register respectively. The watchdog monitor function is enabled by setting the watchdog 

upper and lower threshold monitor function enable bits, ADWUE and ADWLE, in the watchdog 

control register ADCWCR. The channel to be monitored can be specified by configuring the 

ADWCH and ADWALL bits. When the converted data is less or higher than the lower or upper 

threshold, as defined by the ADLT bit field and ADUT bit field in the ADCTR register respectively, 

the watchdog lower or upper threshold interrupt raw flags, ADIRAWL or ADIRAWU in the 

ADCIRAW register, will be asserted if the watchdog lower or upper threshold monitor function 

is enabled. If the lower or upper threshold interrupt raw flag is asserted and the corresponding 

interrupt is enabled by setting the ADIEL or ADIEU bit in the ADCIER register, the A/D watchdog 

lower or upper threshold interrupt will be generated.

Содержание HT32F50231







































































































































































































































































































































































































































































































Отзывы:

Нет отзывов