Rev. 1.20
�4
�an�a�� 2�� 201�
Rev. 1.20
��
�an�a�� 2�� 201�
BS82B12A-3/BS82C16A-3/BS82D20A-3
Touch Key 8-Bit Flash MCU with LED/LCD Driver
BS82B12A-3/BS82C16A-3/BS82D20A-3
Touch Key 8-Bit Flash MCU with LED/LCD Driver
Entering the IDLE0 Mode
There is only one way for the devices to enter the IDLE0 Mode and that is to execute the "HALT"
instruction in the application program with the IDLEN bit in SMOD register equal to "1" and the
FSYSON bit in CTRL register equal to "0". When this instruction is executed under the conditions
described above, the following will occur:
• The system clock will be stopped and the application program will stop at the "HALT" instruc-
tion, but the low frequency f
SUB
clock will be on.
• The Data Memory contents and registers will maintain their present condition.
• The WDT will be cleared and resume counting.
• The I/O ports will maintain their present conditions.
• In the status register, the Power Down flag, PDF, will be set and the Watchdog time-out flag, TO,
will be cleared.
Entering the IDLE1 Mode
There is only one way for the devices to enter the IDLE1 Mode and that is to execute the "HALT"
instruction in the application program with the IDLEN bit in SMOD register equal to "1" and the
FSYSON bit in CTRL register equal to "1". When this instruction is executed under the conditions
described above, the following will occur:
• The system clock and the low frequency f
SUB
will be on and the application program will stop at
the "HALT" instruction.
• The Data Memory contents and registers will maintain their present condition.
• The WDT will be cleared and resume counting
.
• The I/O ports will maintain their present conditions.
• In the status register, the Power Down flag, PDF, will be set and the Watchdog time-out flag, TO,
will be cleared.
Standby Current Considerations
As the main reason for entering the SLEEP or IDLE Mode is to keep the current consumption of
the devices to as low a value as possible, perhaps only in the order of several micro-amps except
in the IDLE1 Mode, there are other considerations which must also be taken into account by the
circuit designer if the power consumption is to be minimised. Special attention must be made to
the I/O pins on the device. All high-impedance input pins must be connected to either a fixed high
or low level as any floating input pins could create internal oscillations and result in increased
current consumption. This also applies to devices which have different package types, as there may
be unbonbed pins. These must either be setup as outputs or if setup as inputs must have pull-high
resistors connected.
Care must also be taken with the loads, which are connected to I/O pins, which are setup as
outputs. These should be placed in a condition in which minimum current is drawn or connected
only to external circuits that do not draw current, such as other CMOS inputs. In the IDLE1 Mode
the system oscillator is on, if the system oscillator is from the high speed system oscillator, the
additional standby current will also be perhaps in the order of several hundred micro-amps
.
Содержание BS82B12A-3
Страница 33: ...Rev 1 20 33 January 23 2015 BS82B12A 3 BS82C16A 3 BS82D20A 3 Touch Key 8 Bit Flash MCU with LED LCD Driver ...
Страница 34: ...Rev 1 20 34 January 23 2015 BS82B12A 3 BS82C16A 3 BS82D20A 3 Touch Key 8 Bit Flash MCU with LED LCD Driver ...
Страница 35: ...Rev 1 20 35 January 23 2015 BS82B12A 3 BS82C16A 3 BS82D20A 3 Touch Key 8 Bit Flash MCU with LED LCD Driver ...
