manualshive.com logo in svg

Holtek BS82B12A-3, Руководство пользователя

"Компания Holtek представляет готовое решение для интеграции BS82B12A-3. На нашем веб-сайте вы можете бесплатно скачать инструкцию по использованию этого продукта. Данное устройство обеспечит надежную работу вашего проекта. Скачивайте руководство с manualshive.com прямо сейчас!"

Поделиться
Скачать
background image

Rev. 1.20

126

�an�a�� 2�� 201�

Rev. 1.20

127

�an�a�� 2�� 201�

BS82B12A-3/BS82C16A-3/BS82D20A-3

Touch Key 8-Bit Flash MCU with LED/LCD Driver

BS82B12A-3/BS82C16A-3/BS82D20A-3

Touch Key 8-Bit Flash MCU with LED/LCD Driver

UART Transmitter

Data word lengths of either 8 or 9 bits can be selected by programming the BNO bit in the UCR1 
register. When BNO bit is set, the word length will be set to 9 bits. In this case the 9th bit, which 
is the MSB, needs to be stored in the TX8 bit in the UCR1 register. At the transmitter core lies the 
Transmitter Shift Register, more commonly known as the TSR, whose data is obtained from the 
transmit data register, which is known as the TXR register. The data to be transmitted is loaded 
into this TXR register by the application program. The TSR register is not written to with new data 
until the stop bit from the previous transmission has been sent out. As soon as this stop bit has been 
transmitted, the TSR can then be loaded with new data from the TXR register, if it is available. It 
should be noted that the TSR register, unlike many other registers, is not directly mapped into the 
Data Memory area and as such is not available to the application program for direct read/write 
operations. An actual transmission of data will normally be enabled when the TXEN bit is set, but 
the data will not be transmitted until the TXR register has been loaded with data and the baud rate 
generator has defined a shift clock source. However, the transmission can also be initiated by first 
loading data into the TXR register, after which the TXEN bit can be set. When a transmission of 
data begins, the TSR is normally empty, in which case a transfer to the TXR register will result in 
an immediate transfer to the TSR. If during a transmission the TXEN bit is cleared, the transmission 
will immediately cease and the transmitter will be reset. The TX output pin will then return to the I/
O or other pin-shared function.

Transmitting Data

When the UART is transmitting data, the data is shifted on the TX pin from the shift register, with 
the least significant bit first. In the transmit mode, the TXR register forms a buffer between the 
internal bus and the transmitter shift register. It should be noted that if 9-bit data format has been 
selected, then the MSB will be taken from the TX8 bit in the UCR1 register. The steps to initiate a 
data transfer can be summarized as follows:

•  Make the correct selection of the BNO, PRT, PREN and STOPS bits to define the required word 

length, parity type and number of stop bits.

•  Setup the BRG register to select the desired baud rate.
•  Set the TXEN bit to ensure that the UART transmitter is enabled and the TX pin is used as a 

UART transmitter pin.

•  Access the USR register and write the data that is to be transmitted into the TXR register. Note 

that this step will clear the TXIF bit.

This sequence of events can now be repeated to send additional data. It should be noted that when 
TXIF is 

"

0", data will be inhibited from being written to the TXR register. Clearing the TXIF flag is 

always achieved using the following software sequence:

•  A USR register access
•  A TXR register write execution

The read-only TXIF flag is set by the UART hardware and if set indicates that the TXR register is 
empty and that other data can now be written into the TXR register without overwriting the previous 
data. If the TEIE bit is set then the TXIF flag will generate an interrupt. During a data transmission, 
a write instruction to the TXR register will place the data into the TXR register, which will be 
copied to the shift register at the end of the present transmission. When there is no data transmission 
in progress, a write instruction to the TXR register will place the data directly into the shift register, 
resulting in the commencement of data transmission, and the TXIF bit being immediately set. When 
a frame transmission is complete, which happens after stop bits are sent or after the break frame, the 
TIDLE bit will be set. To clear the TIDLE bit the following software sequence is used:

•  A USR register access
•  A TXR register write execution

Note that both the TXIF and TIDLE bits are cleared by the same software sequence.

Содержание BS82B12A-3









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BS82B12A-3

iCeeO2 C30 Instruction Manual preview
C30
Бренд: iCeeO2 Страницы: 7
Y-Solar Smart-MPPT Li Series User Manual preview
Smart-MPPT Li Series
Бренд: Y-Solar Страницы: 6
Parker ER Series Maintenance Instructions & Parts List preview
ER Series
Бренд: Parker Страницы: 44
National Instruments CompactRIO cRIO-9002 Operating Instructions Manual preview
CompactRIO cRIO-9002
Бренд: National Instruments Страницы: 21
National Instruments cDAQ-9133 User Manual preview
cDAQ-9133
Бренд: National Instruments Страницы: 145
National Instruments cRIO-9039 User Manual preview
cRIO-9039
Бренд: National Instruments Страницы: 42
National Instruments cDAQ-9132 Safety, Environmental, And Regulatory Information preview
cDAQ-9132
Бренд: National Instruments Страницы: 8
W.E.ST. SCU-138-P Technical Documentation Manual preview
SCU-138-P
Бренд: W.E.ST. Страницы: 34
Ltech TT-DX-R4-5A Manual preview
TT-DX-R4-5A
Бренд: Ltech Страницы: 4
Motor Guard M-60R Instructions preview
M-60R
Бренд: Motor Guard Страницы: 2
SKF Ecomag Installation, Operation And Maintenance Manual preview
Ecomag
Бренд: SKF Страницы: 11
Danfoss VT2800 Series Design Manual preview
VT2800 Series
Бренд: Danfoss Страницы: 162
National Instruments cRIO-9064 User Manual preview
cRIO-9064
Бренд: National Instruments Страницы: 26
Continental Instruments CICP1800T Datasheet preview
CICP1800T
Бренд: Continental Instruments Страницы: 2
ST STM32F469 Series User Manual preview
STM32F469 Series
Бренд: ST Страницы: 31
DPS Telecom NetGuardian LPG D-PK-NGLPG User Manual preview
NetGuardian LPG D-PK-NGLPG
Бренд: DPS Telecom Страницы: 82
WAGO 8003 Series Operating And Assembly Instructions preview
8003 Series
Бренд: WAGO Страницы: 2
SIATA PS0335 XP0/05 Service Manual preview
PS0335 XP0/05
Бренд: SIATA Страницы: 7

Бренды по названию

Популярные бренды

Загрузить еще бренды