Rev. 1.20
122
�an�a�� 2�� 201�
Rev. 1.20
12�
�an�a�� 2�� 201�
BS82B12A-3/BS82C16A-3/BS82D20A-3
Touch Key 8-Bit Flash MCU with LED/LCD Driver
BS82B12A-3/BS82C16A-3/BS82D20A-3
Touch Key 8-Bit Flash MCU with LED/LCD Driver
Bit 5
BRGH
: Baud Rate speed selection
0: Low speed baud rate
1: High speed baud rate
The bit named BRGH selects the high or low speed mode of the Baud Rate Generator.
This bit, together with the value placed in the baud rate register BRG, controls the
Baud Rate of the UART. If this bit is equal to "1", the high speed mode is selected. If
the bit is equal to "0", the low speed mode is selected.
Bit 4
ADDEN
: Address detect function enable control
0: Address detection function is disabled
1: Address detection function is enabled
The bit named ADDEN is the address detect function enable control bit. When this
bit is equal to "1", the address detect function is enabled. When it occurs, if the 8th
bit, which corresponds to RX7 if BNO=0 or the 9th bit, which corresponds to RX8 if
BNO=1, has a value of "1", then the received word will be identified as an address,
rather than data. If the corresponding interrupt is enabled, an interrupt request will be
generated each time the received word has the address bit set, which is the 8th or 9th
bit depending on the value of BNO. If the address bit known as the 8th or 9th bit of the
received word is "0" with the address detect function being enabled, an interrupt will
not be generated and the received data will be discarded.
Bit 3
WAKE
: RX pin falling edge wake-up function enable control
0: RX pin wake-up function is disabled
1: RX pin wake-up function is enabled
This bit enables or disables the receiver wake-up function. If this bit is equal to "1"
and the device is in the IDLE0 or SLEEP mode, a falling edge on the RX input pin
will wake-up the device. If this bit is equal to "0" and the device is in the IDLE or
SLEEP mode, any edge transitions on the RX pin will not wake-up the device.
Bit 2
RIE
: Receiver interrupt enable control
0: Receiver related interrupt is disabled
1: Receiver related interrupt is enabled
This bit enables or disables the receiver interrupt. If this bit is equal to "1" and when
the receiver overrun flag OERR or receive data available flag RXIF is set, the UART
interrupt request flag will be set. If this bit is equal to "0", the UART interrupt request
flag will not be influenced by the condition of the OERR or RXIF flags.
Bit 1
TIIE
: Transmitter Idle interrupt enable control
0: Transmitter idle interrupt is disabled
1: Transmitter idle interrupt is enabled
This bit enables or disables the transmitter idle interrupt. If this bit is equal to "1" and
when the transmitter idle flag TIDLE is set, due to a transmitter idle condition, the
UART interrupt request flag will be set. If this bit is equal to "0", the UART interrupt
request flag will not be influenced by the condition of the TIDLE flag.
Bit 0
TEIE
: Transmitter Empty interrupt enable control
0: Transmitter empty interrupt is disabled
1: Transmitter empty interrupt is enabled
This bit enables or disables the transmitter empty interrupt. If this bit is equal to "1"
and when the transmitter empty flag TXIF is set, due to a transmitter empty condition,
the UART interrupt request flag will be set. If this bit is equal to "0", the UART
interrupt request flag will not be influenced by the condition of the TXIF flag.
Содержание BS82B12A-3
Страница 33: ...Rev 1 20 33 January 23 2015 BS82B12A 3 BS82C16A 3 BS82D20A 3 Touch Key 8 Bit Flash MCU with LED LCD Driver ...
Страница 34: ...Rev 1 20 34 January 23 2015 BS82B12A 3 BS82C16A 3 BS82D20A 3 Touch Key 8 Bit Flash MCU with LED LCD Driver ...
Страница 35: ...Rev 1 20 35 January 23 2015 BS82B12A 3 BS82C16A 3 BS82D20A 3 Touch Key 8 Bit Flash MCU with LED LCD Driver ...